JUKI APW-896/IP-420 Скачать руководство пользователя страница 131

Страница: 131 / 140

− 127 −

Error code

Description of error

How to recover

E358

Corner knife on the moving side, right is held lifted.

Possible to
re-start after

reset.

E359

Corner knife on the fixing side, left is held lifted.

Possible to
re-start after

reset.

E360

Corner knife on the fixing side, right is held lifted.

Possible to
re-start after

reset.

E361

Corner knife on the moving side, left fails to lift.

Possible to
re-start after

reset.

E362

Corner knife on the moving side, right fails to lift.

Possible to
re-start after

reset.

E363

Corner knife on the fixing side, left fails to lift.

Possible to
re-start after

reset.

E364

Corner knife on the fixing side fails to lift.

Possible to
re-start after

reset.

E366

Center knife does not lower.

Possible to
re-start after

reset.

E367

Corner knife cannot be entered.

Possible to
re-start after

reset.

E368

Zipper has run out.

Possible to
re-start after

reset.

E369

Roller stacker lower end sensor does not detect.

Possible to
re-start after

reset.

Содержание APW-896/IP-420













































































































































Результаты поиска

Содержание APW-896/IP-420

Отзывы:

JUKI APW-896/IP-420, Инструкция по эксплуатации, Страница: 131 / 140

Результаты поиска

Содержание APW-896/IP-420

Отзывы: