JUKI APW-896/IP-420 Скачать руководство пользователя страница 72

Страница: 72 / 140

− 68 −

No.

Item

Setting range

Edit unit

Initial value

Changeover of compensation of flap concealed stitching position

using deflection detection

When the automatic deflection detection of left flap is not set, compensation of

flap concealed stitching is automatically performed using the second flap sensor.

＊

When the automatic deflection detection is set, compensation of

flap concealed stitching is automatically performed regardless of

wth/wthout ths settng.

- - -

Used

Not used

Changeover of right/wrong side of material in the corner knife

setting screen

Material displayed in the corner knife setting screen is selected to right

sde dsplay or wrong sde dsplay.

- - -

Rght sde dsplay

Wrong sde dsplay

Stacker timer 5

Sets the waiting time of the stacker from the start of material grasping

operation to the release of the material

Ths settng s avalable when

"Grasping stacker (optional)" is used.

0.00 -

9.99/

0.01 sec

1.00 sec

Stacker timer 6

Sets the duration of operating the oscillating arm

Ths settng s avalable when

"Grasping stacker (optional)" is used.

0.00 -

9.99/

0.01 sec

1.50 sec

Number of stitches of grease-up

Number of stitches of sewing machine motion after replenishing

grease s ndcated.

＊

When pressing CLEAR button, number of stitches is cleared to “0”.

Be sure to clear after replenishing grease.

- - -

Language selection

Language to be ndcated n the panel s selected.

- - -

No selecton

Japanese

Englsh

Chnese

(tradtonal)

Chnese

(simplified)

Spansh

Italian

French

German

Portuguese

Vetnamese

Korean

Indonesian

Russan

. . . Item that is not displayed due to other setting state.

Содержание APW-896/IP-420













































































































































Результаты поиска

Содержание APW-896/IP-420

Отзывы:

JUKI APW-896/IP-420, Инструкция по эксплуатации, Страница: 72 / 140

Результаты поиска

Содержание APW-896/IP-420

Отзывы: