JUKI APW-896/IP-420 Скачать руководство пользователя страница 59

Страница: 59 / 140

− 55 −

No.

Item

Setting range

Edit unit

Initial value

Automatic detection function of deflection at the start of sewing

Flap is read at the start of sewing using two flap sensors and deflection is

automatcally set.

＊

When

Right flap angle detection device is not mounted, left flap

(double welt and single welt with one side flap) only can be used.

- - -

Automatic detection function of deflection at the end of sewing

Flap is read at the end of sewing using two flap sensors and deflection is

automatcally set.

＊

When

Right flap angle detection device is not mounted, left flap

(double welt and single welt with one side flap) only can be used.

- - -

Roller stacker stop/motion change-over

Stop/motion of roller stacker is selected.

＊

It is displayed only when

s set to roller stacker mountng.

- - -

Stop

Moton

Clamp bar stacker stop/motion change-over

Stop/motion of clamp bar stacker is selected.

＊

It is displayed only when

s set to clamp bar stacker mountng.

- - -

Stop

Moton

. . . Item that is not displayed due to other setting state

Содержание APW-896/IP-420













































































































































Результаты поиска

Содержание APW-896/IP-420

Отзывы:

JUKI APW-896/IP-420, Инструкция по эксплуатации, Страница: 59 / 140

Результаты поиска

Содержание APW-896/IP-420

Отзывы: