JUKI APW-896/IP-420 Скачать руководство пользователя страница 77

Страница: 77 / 140

− 73 −

10. PERFORMING OPTIONAL SETTING

(1) Changing procedure of the optional setting

Displaying the 2nd screen of the operation-mode changeover

screen.

When you keep operation-mode changeover key

held

pressed for six seconds, right-scroll button

s dsplayed

on the screen.

When you press this button, the 2nd screen (screen A) of the
operation-mode changeover screen is displayed.

Displaying the option setting list screen

Opton settng button

s dsplayed on the screen.

When you press ths button, opton settng lst screen (screen B)
s dsplayed.

Selecting the option setting you want to change

Press up/down scroll buttons

to select the data tem

button

you want to change.

Optional setting list screen

(Screen B)

Second screen of the

mode changeover screen

(Screen A)

Содержание APW-896/IP-420













































































































































Результаты поиска

Содержание APW-896/IP-420

Отзывы:

JUKI APW-896/IP-420, Инструкция по эксплуатации, Страница: 77 / 140

Результаты поиска

Содержание APW-896/IP-420

Отзывы: