JUKI APW-896/IP-420 Скачать руководство пользователя страница 87

Страница: 87 / 140

− 83 −

The direct buttons have not been registered at the time of your purchase.

Register the direct pattern.

When DIRECT PATTERN REGISTER button

s pressed, the

direct pattern register list screen (screen A) is displayed.

Direct pattern list screen (Screen A)

In the direct pattern list screen, the pattern data of independent
sewing/alternate sewing/cycle sewing can be freely registered up

to 30.

and the drect pattern selecton screen

(screen B) s dsplayed.

Select the pattern you desire to register with PATTERN
SELECTION button

In addition, the ten keys are displayed by pressing NO. INPUT

button

and the pattern you desre to regster can be selected

by nputtng the ten keys.

When ENTER button

s pressed, regster to the drect button s

completed and the screen returns to the drect pattern lst screen

(screen A).

When MODE CHANGEOVER button

s pressed, the sewng

mode s changed over to ndependent sewng

→

alternate sewng

→

cycle sewng.

Direct pattern selection screen

(Screen B)

When the selected button is pressed again, the selection is

released.

Содержание APW-896/IP-420













































































































































Результаты поиска

Содержание APW-896/IP-420

Отзывы:

JUKI APW-896/IP-420, Инструкция по эксплуатации, Страница: 87 / 140

Результаты поиска

Содержание APW-896/IP-420

Отзывы: