JUKI APW-896/IP-420 Скачать руководство пользователя страница 95

Страница: 95 / 140

− 91 −

(5) Observing the operation measurement information

Display the operation measurement screen

Press OPERATION MEASUREMENT SCREEN DISPLAY button

in the information screen. The operation measurement

screen (screen A) is displayed.

Information on the following 5 items is displayed in the operation

measurement screen.

: This item automatically displays the operation rate from the

time of starting the measurement.

: Ths tem automatcally dsplays the mean machne speed

from the time of starting the measurement.

: This item automatically displays the mean pitch time from the

time of starting the measurement.

: This item automatically displays the mean machine time from

the time of starting the measurement.

: This item displays the number of times of thread trimming per

process.

Input the number of times referring to item

below.

Input the number of times of thread trimming

Next, input the number of times of thread trimming per process.

Press NUMBER OF TIMES OF THREAD TRIMMING button

and the number of times of thread trimming input

screen s dsplayed.

Input the value you desire with ten keys or UP/DOWN buttons.

After the input, press ENTER button

＊

When the input value is “0”, count of the number of times
of thread trimming is not performed. Use this function by

connectng the external swtch.

Operation measurement screen

(Screen A)

Содержание APW-896/IP-420













































































































































Результаты поиска

Содержание APW-896/IP-420

Отзывы:

JUKI APW-896/IP-420, Инструкция по эксплуатации, Страница: 95 / 140

Результаты поиска

Содержание APW-896/IP-420

Отзывы: