manualshive.com logo in svg

JLG 680S, Руководство по обслуживанию и ремонту

JLG 680S – это мощная платформа с большой грузоподъемностью. Для обеспечения долговечности и безопасной эксплуатации необходимо регулярное обслуживание. Скачайте инструкцию по обслуживанию и ремонту бесплатно на manualshive.com и следуйте ей для сохранения высокой производительности вашего оборудования.

Поделиться
Скачать
background image

SECTION 7 - BASIC ELECTRICAL INFORMATION & SCHEMATICS

7-4

3121234

3.

Anderson connectors for the battery boxes and battery
chargers should have silicone grease applied to the con-
tacts only.

NOTE:

Curing-type sealants might also be used to prevent short-
ing and would be less messy, but would make future pin
removal more difficult.

When applied to electrical connections, dielectric grease helps
to prevent corrosion of electrical contacts and improper con-
ductivity between contacts from moisture intrusion. Open and
sealed connectors benefit from the application of dielectric
grease.

Dielectric grease shall be applied to all electrical connectors at
the time of connection (except those noted under Exclusions). 

Installation of Dielectric Grease

Before following these instructions, refer to excluded connec-
tor types (See Exclusions below).

1.

Use dielectric grease in a tube for larger connection
points or apply with a syringe for small connectors.

2.

Apply dielectric grease to plug/male connector housing
which typically contains sockets contact/female termi-
nals (fill it approximately full; see example below).

3.

Leave a thin layer of dielectric grease on the face of the
connector.

4.

Assemble the connector system immediately to prevent
moisture ingress or dust contamination.

5.

Pierce one of the unused wire seals prior to assembly if
the connector system tends to trap air (i.e. AMP Seal)
and then install a seal plug. 

Deutsch HD, DT, DTM, DRC Series

The Deutsch connector system is commonly used for harsh
environment interconnect. Follow the installation instructions.

AMP Seal

The AMP Seal connector system is used on the Control ADE
Platform and Ground Modules.

Apply dielectric grease to the female contact. If trapped air
prevents the connector from latching, pierce one of the
unused wire seals. After assembly, install a seal plug (JLG
#4460905) in that location to prevent moisture ingress.

Note that seal plugs may be installed by the wire harness man-
ufacturer if an unused wire seal becomes compromised (wire
inserted in the wrong cavity during assembly and then cor-
rected).

Figure 7-5.  Application to Plug/Male Contacts

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

D&R ELECTRONICS F5S-IQ Series Installation Manual preview
F5S-IQ Series
Бренд: D&R ELECTRONICS Страницы: 12
stellar labs Slider65 Owner'S Manual preview
Slider65
Бренд: stellar labs Страницы: 52
M-system R7C-DC8C Instruction Manual preview
R7C-DC8C
Бренд: M-system Страницы: 9
Fastech Ezi-IO EtherCAT DA User Manual preview
Ezi-IO EtherCAT DA
Бренд: Fastech Страницы: 52
M-system R8-SS4N Instruction Manual preview
R8-SS4N
Бренд: M-system Страницы: 5
Roland R1000 series E20 Manual preview
R1000 series E20
Бренд: Roland Страницы: 156
ORTAL Heat Control System Installation And Operation Manual preview
Heat Control System
Бренд: ORTAL Страницы: 20
Tews Technologies TIP670 User Manual preview
TIP670
Бренд: Tews Technologies Страницы: 19
Measurement Computing USB-1408FS-Plus User Manual preview
USB-1408FS-Plus
Бренд: Measurement Computing Страницы: 29
Measurement Computing USB-2533 User Manual preview
USB-2533
Бренд: Measurement Computing Страницы: 50
Fasel Elektronik FCU-EXT-APP-CONTROL Installation preview
FCU-EXT-APP-CONTROL
Бренд: Fasel Elektronik Страницы: 2
gala gar Tig 3200 ACDC Technical Instruction Manual preview
Tig 3200 ACDC
Бренд: gala gar Страницы: 67
ZENDEX GO JAK G4107 Manual preview
GO JAK G4107
Бренд: ZENDEX Страницы: 10
M-system EtherCAT R7I4DECT-1-YVF4 Instruction Manual preview
EtherCAT R7I4DECT-1-YVF4
Бренд: M-system Страницы: 10
Argus RSM 48/10 Manual preview
RSM 48/10
Бренд: Argus Страницы: 38
Carl Stahl Kromer CondorLift CSmag 100 User Information preview
CondorLift CSmag 100
Бренд: Carl Stahl Kromer Страницы: 56
Broughton 1450/850 LADDERSPAN User Manual preview
1450/850 LADDERSPAN
Бренд: Broughton Страницы: 19
Bosch PSG 3000 Series Instructions For Assembly And Operation Manual preview
PSG 3000 Series
Бренд: Bosch Страницы: 114

Бренды по названию

Популярные бренды

Загрузить еще бренды