manualshive.com logo in svg

JLG 680S, Руководство по обслуживанию и ремонту

JLG 680S – это мощная платформа с большой грузоподъемностью. Для обеспечения долговечности и безопасной эксплуатации необходимо регулярное обслуживание. Скачайте инструкцию по обслуживанию и ремонту бесплатно на manualshive.com и следуйте ей для сохранения высокой производительности вашего оборудования.

Поделиться
Скачать
background image

SECTION 3 - CHASSIS & TURNTABLE

3-80

3121234

3.14 SWING HUB (PRIOR TO SN 0300134352)

Disassembly

1.

Loosen all 12 cover bolts (12) & (13) and drain the oil

from the unit.

2.

Remove the 12 cover bolts (12) & (13) and lift off the

cover (6). Remove and discard the o-ring (5) from the

counterbore of the cover (6).

3.

Remove the input gear (8) and thrust washer (10).

4.

Lift out the carrier assembly (3) and top thrust washer

(11). The thrust washer (11) may stick to the inside of the

carrier (3).

5.

Remove the input thrust spacer (9).

6.

Lift out the internal gear (2) and thrust washer (11). The

thrust washer (11) may stick to the under side of the car-

rier (3).

7.

Remove the retaining ring (1I) from the output shaft (1A)

and discard.

EYE PROTECTION SHOULD BE WORN DURING RETAINING RING (1I) REMOVAL.

8.

Remove bearing shim (1H) from the output shaft (1A).

9.

The output shaft (1A) may now be pressed out of the

hub (1G).

10.

The bearing cups (1C) & (1E) will remain in hub (1G) as

will bearing cone (1F). Bearing cone (1D) will remain on

the same output shaft (1A). The seal (1B) will be auto-

matically removed during this procedure.

NOTE:

If bearing replacement is necessary, the bearing cups can

be removed with a slide hammer puller driven out with a

punch.

11.

To remove the cluster gears (3F) from the carrier (3A),

drive the anti-roll pin (3G) into the planet shaft (3E) may

now be tapped out of the carrier. After planet shaft (3E)

has been removed the roll pin (3G) can be driven out.

12.

The cluster gear (3F) can now be removed from the car-

rier (3A). The thrust washers (3B) will be removed with

the cluster gear (3F).

13.

The needle rollers (3C) and spacer (3D) are now removed

from the cluster gear (3F).

WHEN REBUILDING OR REPAIRING THE UNIT, THE RETAINING RING (1I), O-
RINGS (5) AND SEAL (1B) SHOULD ALWAYS BE REPLACED.

Main Assembly Procedure

1.

With the hub shaft sub-assembly resting on the shaft
(1A) install internal gear (2). The spline of the internal
gear (2) bore will mesh the spline of the output shaft
(1A).

2.

Thrust washer (11) is installed on the face of the output
shaft (1A). Sufficient grease or petroleum jelly should be
used to hold thrust washer in place.

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Hamma Misceo 3 Instructions Manual preview
Misceo 3
Бренд: Hamma Страницы: 60
Paton PRO-160 Data Sheet And Operating Manual preview
PRO-160
Бренд: Paton Страницы: 31
Keg King King Junior Instruction Manual preview
King Junior
Бренд: Keg King Страницы: 4
Orion L66-20 Manual preview
L66-20
Бренд: Orion Страницы: 23
Laars Mighty Therm 2 Installation And Operation Manual preview
Mighty Therm 2
Бренд: Laars Страницы: 9
WAGO 750-496 Manual preview
750-496
Бренд: WAGO Страницы: 92
REID LIFTING PORTA GANTRY 1100 Assembly & Operation Manual preview
PORTA GANTRY 1100
Бренд: REID LIFTING Страницы: 28
GMI D5244D Instruction & Safety Manual preview
D5244D
Бренд: GMI Страницы: 10
Balluff BNI00E7 User Manual preview
BNI00E7
Бренд: Balluff Страницы: 42
Riello RK Hydroline N Installation Instructions Manual preview
RK Hydroline N
Бренд: Riello Страницы: 20
Magnetic Autocontrol MAGSTOP MIB 10-C090 Operating Instructions Manual preview
MAGSTOP MIB 10-C090
Бренд: Magnetic Autocontrol Страницы: 15
Keithley KPCI-PIO24 User Manual preview
KPCI-PIO24
Бренд: Keithley Страницы: 66
Taylor SYSTEM CD200 SERIES Operating Manual preview
SYSTEM CD200 SERIES
Бренд: Taylor Страницы: 44
Oerlikon CITOTIG 250 AC/DC Safety Instructions For Operation And Maintenance preview
CITOTIG 250 AC/DC
Бренд: Oerlikon Страницы: 136
harbor master Premier Verical Lift Instructions Manual preview
Premier Verical Lift
Бренд: harbor master Страницы: 9
Stryker SwitchPoint Infinity 2 Operation And Maintenance Manual preview
SwitchPoint Infinity 2
Бренд: Stryker Страницы: 82
Philips OccuSwitch Wireless Installation Manual preview
OccuSwitch Wireless
Бренд: Philips Страницы: 2
Philips LDTS07 User Manual preview
LDTS07
Бренд: Philips Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды