JLG 680S Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 530

JLG 680S Скачать руководство пользователя страница 114

SECTION 3 - CHASSIS & TURNTABLE

3-62

3121234

8.

Remove all fittings from the unit. Discard any o-rings on
the fittings.

9.

Using an 11/16 in. hex wrench, loosen the speed sensor
lock nut (14) if equipped. Then remove the speed sensor
using a Vi in. hex wrench. Units without speed sensor
have an o-ring plug (15) installed in that location;
remove it with a Va in. internal hex wrench.

10.

Using a 1/4 in. internal hex wrench, remove control line
plugs (16, 17). Discard o-rings. Using a 3 mm hex
wrench, remove cavity plug (18, if equipped with two-
line control) from X2 cavity.

11.

Using a 5/16 in. internal hex wrench, remove drain plugs
(19, 20). Discard o-rings.

12.

Using a 9/16 in. internal hex wrench, remove work port
plugs (21, if equipped with axial ports). Discard o-rings.

13.

Using an 8 mm internal hex wrench, remove the end
capscrews (22).

14.

Remove the end cap (23). Remove o-ring (24) from the
housing or end cap.

NOTE:

When the end capscrews are removed, pressure from the
servo spring will cause the end cap to bind on the shaft.
Press down on the portion of the end cap covering the
servo piston and hold the end cap level while removing.

15

20

16

16

19

17

18

21

14

14. Lock Nut
15. O-ring Plug
16. Control Line Plug
17. Control Line Plug

18. Cavity Plug
19. Drain Plug
20. Drain Plug
21. Work Port Plug

Figure 3-40. Plugs, Fittings and Speed Sensor

24

22

23

22. Screw
23. End Cap
24. O-ring

Figure 3-41. End Cap

«
...
112
113
114
115
116
...
»

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов