manualshive.com logo in svg

JLG 680S, Руководство по обслуживанию и ремонту

JLG 680S – это мощная платформа с большой грузоподъемностью. Для обеспечения долговечности и безопасной эксплуатации необходимо регулярное обслуживание. Скачайте инструкцию по обслуживанию и ремонту бесплатно на manualshive.com и следуйте ей для сохранения высокой производительности вашего оборудования.

Поделиться
Скачать
background image

SECTION 3 - CHASSIS & TURNTABLE

3121234

3-199

Table 3-12. LPF Fuel System Diagnosis

STEP

ACTION

VALUE(S)

YES

NO

1

Were you referred to this procedure by a DTC diagnostic chart?

- -

Go to Step 3

Go to Step 2

2

Perform the On Board Diagnostic (OBD) System Check.
Are any DTCs present in the ECM?

- -

Go to the                                                                          

applicable DTC Table

Go to Step 3

3

Verify that the LPG fuel tank has a minimum of 1/4 tank of fuel, that the manual valve is open 
and the tank quick connect is fully engaged
Does the vehicle have fuel?

- -

Go to Step 4

- -

4

1. Connect a water column gauge or a manometer to the secondary test port of the low pressure 
regulator (LPR).
2. Start the engine and allow it to reach operating temperature. 
Does the engine start and run?

- -

Go to Step 5

Go to Step 8

5

With the engine idling, observe the pressure reading for the LPR secondary pressure.
Does the fuel pressure fluctuate rhythmically OUTSIDE the specified range?

 -1.0" to

-2.0" w.c

Go to Step 25

Go to Step 6

6

1. Disconnect the EPR electrical connectors. NOTE: This action will cause a DTC to be set by the 
ECM
2. With the engine idling observe the pressure reading on the secondary test port.
Is the fuel pressure WITHIN the specified range?

 -1.0" to 

-2.0" w.c

Go to Fuel Control System 

Diagnosis

Go to Step 7

7

1. Inspect the air intake stream between the mixer assembly and the throttle body for leaks.
 2. Inspect the fuel hose connection between the LPR and mixer assembly for damage or leak-
age.
3. Inspect any vacuum hoses for leaks
 Was a problem found and corrected?

- -

Go to Step 26

Go to Step 22

8

1. Connect a water column gauge or a manometer to the secondary test port of the low pressure 
regulator (LPR).
2. Crank the engine and observe the pressure reading for the LPR secondary pressure.
Does the fuel pressure indicate a vacuum is present?                                                          

- -

Go to Step 12

Go to Step 9

9

1. Remove Air induction hose to the mixer
2. Observe the air valve for movement while the engine is cranking. Note: Movement of the air 
valve will be minimal at cranking speeds.
Does the air valve move when the engine is cranked?                                                        

- -

Go to Step 11

Go to Step 10

10

1. Inspect the air intake stream to the mixer assembly and the throttle body for vacuum leaks.
2. Inspect the vacuum hoses from the mixer for proper connection and condition.
 Was a problem found and repaired?

- -

Go to Step 26

Go to Step 24

11

Inspect the fuel hose connection between the LPR and the mixer assembly for damage or leak-
age.
Was a problem found and repaired?

- -

Go to Step 26

Go to Step 12

12

1. Connect a 0-10 psi gauge to the primary test port of the low pressure regulator (LPR).
2. Crank the engine and observe the pressure reading for the LPR primary pressure.
Is the fuel pressure ABOVE the specified value?

1- 3 PSI

Go to Step 22

Go to Step 13

13

1. Turn OFF the ignition.
2. Disconnect the LPL connector.
3. Install a test light between the pins of the LPL connector.
 4. Crank the engine. The test light should illuminate. 
Does the test light illuminate?

- -

Go to Step 14

Go to Step 16

14

Using a DVOM, check the resistance of the low pressure lock-off (LPL).
Is the resistance within the specified range? 

12

W

 - 16

W

Go to Step 15

Go to Step 23

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Waterway NEO 1200 Instruction Manual preview
NEO 1200
Бренд: Waterway Страницы: 8
Mark Climate Infra Line G20 Technical Manual preview
Infra Line G20
Бренд: Mark Climate Страницы: 60
Lampert PUK04 Operating Manual preview
PUK04
Бренд: Lampert Страницы: 20
Advantech AIIS-1440 User Manual preview
AIIS-1440
Бренд: Advantech Страницы: 82
Quality Heating 3060-150 Manual preview
3060-150
Бренд: Quality Heating Страницы: 15
Joyonway PB554 Simplified Operation Instruction preview
PB554
Бренд: Joyonway Страницы: 8
Paton VDI 160 PRO Manual preview
VDI 160 PRO
Бренд: Paton Страницы: 35
Mithraeum Brewiks 500 User Manual preview
Brewiks 500
Бренд: Mithraeum Страницы: 33
ICP DAS USA I-7017(F)C Quick Start Manual preview
I-7017(F)C
Бренд: ICP DAS USA Страницы: 4
Walkera G120EFI User Manual preview
G120EFI
Бренд: Walkera Страницы: 22
WinSystems PCM-MIO-G-1 Product Manual preview
PCM-MIO-G-1
Бренд: WinSystems Страницы: 30
Eastwood 20636 Instructions Manual preview
20636
Бренд: Eastwood Страницы: 12
Lincoln Electric VINTAGE 400 (CE) IM889-A Operator'S Manual preview
VINTAGE 400 (CE) IM889-A
Бренд: Lincoln Electric Страницы: 49
Intermatic PJB2175 Installation, Operation & Service Manual preview
PJB2175
Бренд: Intermatic Страницы: 2
ICP DAS USA PISO-DA2U Quick Start Manual preview
PISO-DA2U
Бренд: ICP DAS USA Страницы: 7
i4Technology GRAD DUOS S User Manual preview
GRAD DUOS S
Бренд: i4Technology Страницы: 6
ESAB Aristo Mig 3001i Service Manual preview
Aristo Mig 3001i
Бренд: ESAB Страницы: 76
ACC SmarTouch Digital User Manual preview
SmarTouch Digital
Бренд: ACC Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды