manualshive.com logo in svg

JLG 680S, Руководство по обслуживанию и ремонту

JLG 680S – это мощная платформа с большой грузоподъемностью. Для обеспечения долговечности и безопасной эксплуатации необходимо регулярное обслуживание. Скачайте инструкцию по обслуживанию и ремонту бесплатно на manualshive.com и следуйте ей для сохранения высокой производительности вашего оборудования.

Поделиться
Скачать
background image

SECTION 5 - BASIC HYDRAULICS INFORMATION & SCHEMATICS

5-46

3121234

5.4

START UP PROCEDURES

Start Up After Overhaul or Replacement of 
Components

PRE-FILL OF BOTH THE DRIVE AND FUNCTION PUMP

Machine without oil cooler: 

When filling the oil tank, fill it to

the very top of the tank. This will give enough head pressure
from the tank to gravity fill the case on both pumps. The
excess oil will be used to fill the cylinders during start up. The
top case port on the outside of the drive pump has a 3/4 in. tee
fitting. Remove the cap from the end of the tee. You should
see oil in 1-2 minutes, tighten up the cap. The drive pump case
is done. Next, go the function pump, using a 3/8 in. allen
wrench remove the plug on the inside of the pump next to the
turn-table side sheet. When oil flows out of the pump, 2-3 min-
utes, re-install the plug. Both pumps are pre-filled. Not doing
this causes the pumps to start dry, and reduces the efficiency
of the pump and can cause premature failure.

Machine with oil cooler: 

When filling the oil tank, fill it to the

very top of the tank. This will help give enough head pressure
from the tank to gravity fill the case on both pumps. The top
case port on the outside of the pump has a 3/4 in. tee fitting.
Remove the cap from the center of the tee. You should see oil
in 1-2 minutes. If not, depending on hose routing, the drive
pump may not gravity feed. Oil has to flow through the oil
cooler to get to the pump. Hose up an external hand pump to
this tee fitting, and give it about six pumps after it has started
pumping oil. This should be sufficient. Install the cap back
onto the tee fitting. The drive pump is done. Next, go the func-
tion pump, using a 3/8 in. allen wrench remove the plug on
the inside of the pump next to the turn-table side sheet. When
oil flows out of the pump, 2-3 minutes, re-install the plug. Both
pumps are pre-filled. Not doing this causes the pumps to start
dry, and reduces the efficiency of the pump and can cause pre-
mature failure. 

PURGING OF THE FUNCTION PUMP SUCTION HOSE.

Large pockets of air get trapped in this line and must be
removed at low pressure. Head pressure from the tank is not
enough. Here are three methods of purging the air from the
hose at low pressure. 

1.

At the main control valve, remove the 3/4 in. hose from
port “P1” and remove the 1 in. hose from port “T” by
using a 12-16 connector, connect them together. Start
the machine and let it run for approx. 10 seconds. Shut
off the machine, remove the 12-16 adapter and re-hose. 

2.

Remove the 3/4 in. hose from port “P1” and hold it into a
5 gallon bucket and start the machine. The air should
purge very quickly, (seconds). Shut off the machine and
re-hose. 

3.

Remove the 3/4 in. hose from port “P1”, using a #12 male
union add approx. 30 in. of 3/4 in. hose to it. Remove the
return filter cap at the top of the tank, lift out the ele-
ment making sure the canister stays in the tank. Hold
the hose end down in the canister and start the machine
and let it run approx. 10 seconds. Re-install the filter and
re-hose the machine. 

NOTE:

If using a shop vac to create suction on the oil tank while
doing maintenance, both steps “1” and “2” will need done.

NOTE:

If installing a new drive pump, step “1” will need done.

NOTE:

If installing a new function pump, step “1” and “2” will need
done.

NOTE:

If installing a new function pump and the suction hose is
capped without draining a lot of oil out of the hose, which
creates a large air void, step “2” will not need to be done. 

NOTE:

When operating a function such as Lift Up, if the function
pump makes a loud noise and the lift up stops and starts,
that is a sign of cavitation, air going through the pump at
high pressure. This will in a short time destroy the pump
and contaminate the entire system. Make sure all suction
hoses are tight and free of leaks at the tank and pump. A
suction hose does not leak when the engine is running, it
will allow air to be drawn into the pump causing cavita-
tion. After the machine is shut down, then you will see a
very slow leak.

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Wesco Gator Grip Drum EGG-1 Assembly Procedure And Operating Instructions preview
Gator Grip Drum EGG-1
Бренд: Wesco Страницы: 2
Welding Industries Malaysia MIG210S Instruction Manual preview
MIG210S
Бренд: Welding Industries Malaysia Страницы: 20
Bard W24G4 Installation Instructions Manual preview
W24G4
Бренд: Bard Страницы: 54
Lampert PUK U4 Operating Manual preview
PUK U4
Бренд: Lampert Страницы: 22
Skyjack 6826El Operating Manual preview
6826El
Бренд: Skyjack Страницы: 47
H&S AUTOSHOT HSG130 Operator'S Manual preview
HSG130
Бренд: H&S AUTOSHOT Страницы: 19
ICP DAS USA ET-2254 Quick Start Manual preview
ET-2254
Бренд: ICP DAS USA Страницы: 8
WesAudio ngLEVELER User Manual preview
ngLEVELER
Бренд: WesAudio Страницы: 65
Digitrax UT4D User Manual preview
UT4D
Бренд: Digitrax Страницы: 8
AWELCO BLUMIG 145 User Manual preview
BLUMIG 145
Бренд: AWELCO Страницы: 40
Prowise iPro Tilt Lift User Manual preview
iPro Tilt Lift
Бренд: Prowise Страницы: 15
M-system R7D-YV2A Instruction Manual preview
R7D-YV2A
Бренд: M-system Страницы: 10
M-system R7D-YS2A Instruction Manual preview
R7D-YS2A
Бренд: M-system Страницы: 10
M-system R30SVF4 Instruction Manual preview
R30SVF4
Бренд: M-system Страницы: 5
Triax 492060 User Manual preview
492060
Бренд: Triax Страницы: 52
Magmaweld ID PULSE Series Quick User Manual preview
ID PULSE Series
Бренд: Magmaweld Страницы: 8
Yetter AIR ADJUST 2940 Operator'S Manual preview
AIR ADJUST 2940
Бренд: Yetter Страницы: 64
Agrowtek GrowControl GCX Instruction Manual preview
GrowControl GCX
Бренд: Agrowtek Страницы: 78

Бренды по названию

Популярные бренды

Загрузить еще бренды