JLG 680S Скачать руководство пользователя страница 238 | Manualshive

Страница: 238 / 530

background image

SECTION 3 - CHASSIS & TURNTABLE

3-186

3121234

2.

Remove the radiator cap. Fill the radiator with coolant
until coolant starts to appear from the previously
removed hose at the EPR. Reinstall the hose back onto
the EPR and continue to fill radiator with coolant.

3.

With the radiator cap still removed, start the engine and
run until the thermostat opens. The thermostat opens at
170° F (77° C), which can be checked using the JLG
handheld analyzer.

WHILE ENGINE IS RUNNING, AIR AND/OR STEAM MAY BE PRESENT COMING
FROM THE RADIATOR. THIS IS NORMAL.

4.

After running the engine for 5 minutes after it has
reached operating temperature, shut the engine off and
continue to step 5.

WITH THE ENGINE RUNNING OR WHEN SHUTTING OFF THE ENGINE, SOME
HEATED COOLANT MAY SPILL OUT DUE TO AIR "BURPING" OUT OF THE SYS-
TEM WITH THE RADIATOR CAP OFF.

5.

Next, verify that the 2 coolant hoses on the EPR are
warm. If they are not warm repeat step 3 and 4, other-
wise continue to step 6.

A PROPERLY PURGED COOLING SYSTEM WILL YIELD A WARM UPPER RADIA-
TOR HOSE AND A WARM EPR HOSE. IF THE UPPER RADIATOR HOSE AND/OR
EPR HOSE ARE NOT WARM TO THE TOUCH AFTER THE ENGINE HAS RUN FOR 5-
8 MINUTES AFTER REACHING OPERATING TEMPERATURE, THE SYSTEM MAY
STILL CONTAIN AIR. IT MAY BE NECESSARY TO REPEAT THE ABOVE STEPS.

6.

Fill radiator with coolant as needed and install the radia-
tor cap. Next, remove the cap off the coolant recovery
bottle and fill just below the HOT FULL line and reinstall
the caps.

«
...
236
237
238
239
240
...
»

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Бренд: QTS Страницы: 50

Бренд: SainSmart Страницы: 49

Бренд: R. Beck Maschinenbau Страницы: 36

TRANSTIG 200 AC/DC

Бренд: CIGWELD Страницы: 128

Бренд: HURNER Страницы: 57

9 08 01 012 00 8

Бренд: FEIN Service Страницы: 49

Бренд: 3M Страницы: 90

Бренд: Vicon Страницы: 91

Бренд: iSMA CONTROLLI Страницы: 26

Бренд: Interlift Страницы: 6

Бренд: morse Страницы: 5

Бренд: Mesa Страницы: 33

LiftRunner B frames

Бренд: Still Страницы: 108

SIMATIC ET 200M

Бренд: Siemens Страницы: 242

SIMATIC ET 200iS

Бренд: Siemens Страницы: 434

Бренд: Spectra Страницы: 16

FlexView FVS IFP Series

Бренд: Map Страницы: 16

Бренд: Soham Impex Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды