JLG 680S Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 530

background image

SECTION 3 - CHASSIS & TURNTABLE

3121234

3-95

9.

Remove manifold (7) and inspect for cracks surface scor-
ing, brinelling or spalling. Replace manifold if any of
these conditions exist. A polished pattern on the ground
surface from commutator or rotor rotation is normal.
Remove and discard the seal rings (4) that are on both
sides of the manifold.

NOTE:

The manifold is constructed of plates bonded together to
form an integral component not subject tofurtherdisas-
semblyforservice.Compare configuration of both sides oft
hem an if old to ensure that same surface is reassembled
against the rotor set.

10.

Remove rotor set (8) and warplane (9), together to retain
the rotor set in its assembled form, maintaining the
same rotor vane (8C) to stator (8B) contact surfaces. The
drive link (10) may come away from the coupling shaft
(12) with the rotor set, and wearplate.You may have to
shift the rotor set on the warplane to work the drive link
out of the rotor (8A) and warplane. Inspect the rotor set
in its assembled form for nicks, scoring, or spalling on
any surface and for broken or worn splines. If the rotor
set component requires replacement, the complete
rotor set must be replaced as it is a matched set. Inspect
the warplane for cracks, brinelling, or scoring. Discard
seal ring (4) that is between the rotor set and wearplate.

NOTE:

The rotor set (8) components may become disassembled
during service procedures. Marking the surface of the rotor
and stator that is facing UP, with etching ink or grease pen-
cil before removal from Torqlink™ will ensure correct reas-
sembly of rotor into stator and rotor set into Torqlink™.
Marking all rotor components and mating spline compo-
nents for exact repositioning at assembly will ensure maxi-
mum wear life and performance of rotor set and Torqlink™.

NOTE:

Series TG Torqlinks™ may have a rotor set with two stator
halves (8B) with a seal ring (4) between them and two sets
of seven vanes (8C). Discard seal ring only if stator halves
become disassembled during the service procedures.

NOTE:

A polished pattern on the wear plate from rotor rotation is
normal.

11.

Place rotor set (8) and wear plate (9) on a flat surface and
center rotor (8A) in stator (8B) such that two rotor lobes
(180 degrees apart) and a roller vane (8C) centerline are
on the same stator centerline. Check the rotor lobe to
roller vane clearance with a feeler gage at this common
centerline. If there is more than 0.005 in. (0.13 mm) of
clearance, replace rotor set.

«
...
145
146
147
148
149
...
»

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Бренд: dbx Страницы: 52

Бренд: cinetto Страницы: 56

Бренд: Orion Страницы: 23

CIRCOtransfer 30 E

Бренд: wagner solar Страницы: 32

Бренд: Link Страницы: 11

Бренд: ICP DAS USA Страницы: 4

NOTIFIER CBC-CLASS 1

Бренд: Pittway Страницы: 20

Бренд: M-system Страницы: 3

Бренд: Sherman Страницы: 14

Бренд: Miller Electric Страницы: 36

Бренд: IMS Страницы: 44

Бренд: AB Quality Страницы: 12

Бренд: Sunex Tools Страницы: 6

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 50

SIMATIC S7-1500R/H

Бренд: Siemens Страницы: 46

Бренд: Siemens Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды