Jennic JN5142 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 95

background image

44

JN-DS-JN5142 1v0

© NXP Laboratories UK 2012

12 Pulse Counters

Two 16-bit counters are provided that can increment during all modes of operation (including sleep).  The first, PC0,
increments from pulses received on DIO1.  The other pulse counter, PC1, can also be accessed on DIO5 or DIO8
depending upon the configuration.  This is enabled under software control.  The pulses can be de-bounced using the
32kHz clock to guard against false counting on slow or noisy edges.  Increments occur from a configurable rising or
falling edge on the respective DIO input.

Each counter has an associated 16-bit reference that is loaded by the user.  An interrupt (and wakeup event if
asleep) may be generated when a counter reaches its pre-configured reference value.  The two counters may
optionally be cascaded together to provide a single 32-bit counter, linked to DIO1.  The counters do not saturate at
65535, but naturally roll-over to 0. Additionally, the pulse counting continues when the reference value is reached
without software interaction so that pulses are not missed even if there is a long delay before an interrupt is serviced
or during the wakeup process.

The system can work with signals up to 100kHz, with no debounce, or from 5.3kHz to 1.7kHz with debounce. When
using debounce the 32kHz clock must be active, so for minimum sleep currents the debounce mode should not be
used.

«
...
42
43
44
45
46
...
»

Содержание JN5142
































































































Отзывы:

Нет отзывов

Похожие инструкции для JN5142

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: Rain Bird Страницы: 138

Бренд: NAiS Страницы: 144

Бренд: OJ Electronics Страницы: 8

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 26

Бренд: Danfoss Страницы: 8

Bell & Gossett Technologic PPS

Бренд: Xylem Страницы: 20

Cutler-Hammer S701X25N3BP

Бренд: Eaton Страницы: 4

RailBoss 4 Basic

Бренд: G-Scale Graphics Страницы: 22

Бренд: Interactive Technologies Страницы: 431

Бренд: H3C Страницы: 32

Бренд: DekoLight Страницы: 48

Бренд: Magnimage Страницы: 31

Бренд: Hanna Instruments Страницы: 28

CompleteStat CS9B-THOA

Бренд: Bard Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды