J&M Nitro Gro 5010 Скачать руководство пользователя страница 13

Страница: 13 / 43

6. Attach jack mounting bracket (JM0031545) to the mounting plate which is welded on the underside of the

frame using a 1” x 6” bolt and 1” centerlock hex nut.

7. Using a fork lift or overhead hoist, lift the front end of the applicator off the ground enough to align the four

holes on the jack (JM0030054) with the four holes on the mounting bracket. Secure the jack to the mounting

bracket with (4) 5/8” x 2” Gr8 hex bolts and (4) 5/8” centerlock hex nuts. Tighten the bolts and keep the jack in

place using the 3/4” L-pin for mounting plate centerlock pin for top of the jack.

8. Run the 1-1/2” x 180” (JM0040330) hose for 5010 applicator or 1-1/2” x 228” (JM0040211) for the 5016

applicator from the back to the front of the applicator. Let it sit loose for the next couple of steps on the

passenger side.

9. Attach pump mounting bracket (JM0034960) using (2) 3/8” x 1” serrated flange bolts and (2) 3/8” serrated

flange nuts. Attach pump using (2) 3/8” x 1-1/2” bolts and (2) 3/8” serrated flange nuts on rear tank saddle

front plate.

Tank

Содержание Nitro Gro 5010












































Результаты поиска

Содержание Nitro Gro 5010

Отзывы:

Похожие инструкции для Nitro Gro 5010

Бренды по названию

Популярные бренды

J&M Nitro Gro 5010, Руководство пользователя

Результаты поиска

Содержание Nitro Gro 5010

Отзывы:

Похожие инструкции для Nitro Gro 5010

Бренды по названию

Популярные бренды