background image

Irrtum und technische Änderungen vorbehalten. Copyright JAMARA e.K. 2015 

Kopie und Nachdruck, auch auszugsweise, nur mit Genehmigung von JAMARA e. K.

JAMARA e.K.
Inh. Manuel Natterer
Am Lauerbühl 5 - DE-88317 Aichstetten
Tel. +49 (0) 75 65/94 12-0 - Fax +49 (0) 75 65/94 12-23

[email protected] 

 www.jamara.com

Service - Tel. +49 (0) 75 65/94 12-66
kundenservice@ jamara.com

ATTENTION!

•  This product is not intended for use by individuals (including children) 

  with reduced physical, sensory or mental capabilities or lack of

  experience and / or knowledge, unless they are supervised by a person 

  responsible for their safety and is able to give instructions about how 
  the product should be used. Children should be supervised to ensure 
  that they do not play with the product.

•   Keep the model away from Children in case it is not appropriate to be 

  used by a Child (see note of age). Keep children away during assembly.

GB - Security instructions

•  Read the instructions and security instructions carefully before 

  using the model.

•   Build the model exactly as directed and plan together.

•   The user is fully responsible for the construction and the correct use of 

 

the model.

•   If this model is the first radio controlled model which you are attempting 

  to build or run, you should secure the assistance of an experienced 

  model pilot. Your local dealer will be able to assist you in locating your 

  local model model sport club or experienced pilots in your area.

•   You should use our recommended accessories (battery, motor, etc.), 

 

note the enclosed instructions.

•   Warning: Risk of eye injury! Keep a safe distance of at least

  1 -2 m to protect themselves and others from injury.

•   To avoid accidents, never fly the model near or over people or animals. 

 

Keep hands, hair and loose clothing away from the rotor, not reach into 

 

the rotors.

•   Do not expose the model or batteries to direct sunlight, always

 

keep them in the shade.

Attention!
In some countries it is a legal requirement to carry third party
indemnity insurance when operating a radio controlled
model. Please ask your local dealer, governing body or your
insurance company for details.

Operating

•  The model can only be flown in good weather.

  Do not fly in wind, rain or thunder storms. 

•  Find a place to fly which complies with any laws, and is free

  from obstacles such as trees, houses and / or other obstacles.

• 

NEVER 

use the model near an airport, railway or roads. Always keep a 

 

safe distance from potentially hazardous and specially protected areas. 

•  Do not operate your model near radio stations, power lines, transformer 

  boxes or similar facilities! This can result in radio interference, causing 

 

loss of control over the model.

•  Before you start, make sure that the frequency channel you are using is 

 

actually free.

•  Never fly out of the reach of your transmitter.

•   Inspect the model before and after every drive for damage and loosing 

 

screws and plug connections. The operator is responsible for any

  damage caused by the operation of flying models.

DE - Spare parts

without illustration

without illustration

No. 16 0340

Cowl

No. 16 0341

Landing gear

No. 16 0342

Fuselage upper part

No. 16 0343

Decal sheet

Service centre 

Reitter Modellbau Versand

Patricia Reitter

Degerfeldstrasse 11

72461 Albstadt

Tel          07432 9802700

Fax         07432 2009594

Mail       [email protected]

Web      www.modellbauversand.de

Extra Trade  

       

Rudolf Müller & Gerrit Müller GdbR

Lindenstraße 82

66787 Wadgassen

Tel          06834 9604952

Fax         06834 9604963

Mail       [email protected]

Web      www.extra-trade.de

Sigi‘s Modellbau Shop   

Siegfried Costa

Bundesstr. 30

AT -6923 Lauterach

Tel          +43 557483657

Fax         +43 557483657

Mail       [email protected]

Web      www.playland-modellbau.at

Modellbau Zentral   

                                                                    

Peter Hofer

Bresteneggstrasse 2

CH -6460 Altdorf

Tel          +41 794296225

Fax         +41 418700213

Mail       [email protected]

Web      www.modellbau-zentral.ch

Bay-Tec Modelltechnik    

                                                          

Martin Schaaf

Am Bahndamm 6

86650 Wemding

Tel          07151 5002192

Fax         07151 5002193

Mail       [email protected]

Web      www.bay-tec.de

DE

DE

DE

Aigner Modellbau    

                                                                    

Edmund Aigner

Graben 2

AT -3300 Amstetten

Tel          +43 747224655

Fax         +43 747223358

Mail       [email protected]

Web      www.modellbau-amstetten.at

CH

AT

AT

Содержание Fokker DVII





























Отзывы: