ITW GSE 6400 Tier 4 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 105

background image

Operation Manual – ITW GSE 6400 Tier 4

2) Lubrication

a) General

Proper lubrication is one of the most important steps in good maintenance procedure. Proper
lubrication means the use of correct lubricants and adherence to a proper time schedule.
Lubrication points, frequency of lubrication, recommended lubricants and filters are indicated in
Figures 2-2-1 and 2-2-2.

This section incorporates the engine maker’s, engine lubrication recommendations from their
Operation and Maintenance Manual.

b) Lubrication

schedule

Time schedules indicated on the Maintenance Schedule, Figure 2-2-1, are approximate and
based on average operating conditions. It may be necessary to lubricate more frequently under
severe operating conditions such as: low engine temperatures, high oil temperatures, or
intermittent operation. However, time intervals should not exceed those indicated in the chart
without careful evaluation.

c) Oil

specification

The engine lubricating oil that is recommended by the engine manufacturer is identified by an API
(American Petroleum Institute) classification designation. The manufacturer does not recommend
any specific brand of lubricating oil.

The use of quality lubricating oil, combined with appropriate lubricating oil drain and filter change
intervals, are important factors in extending engine life.

Oil Type

Use oil specification API CF-4, HT/HS Viscosity 3.7cP minimum.

Oil recommended for the diesel engines in this application is API Class CCMC.

Refer to the manufacturer’s operation manual.

Capacity

Approximately 10 quarts (9.5 liters)

Oil Filter
Replacement
Part Number

Cummins: LF9279

Lube Oil Viscosity
Required as per
Ambient
Temperatures

VISCOSITY

AMBIENT TEMPERATURE CONDITIONS

SAE 15W40 (Preferred)

SAE 10W30

SAE 5W30

SAE 0W30

0ºF (-18ºC) and above for most climates

-10ºF to +50ºF (-23ºC to +10ºC) Winter conditions

-20ºF to +50ºF (-29ºC to +10ºC) Arctic Conditions

-20ºF and below to +50ºF (-29ºC and Below to +10ºC)

Synthetic Oils

See the engine manufacturer’s operations manual for usable synthetic oils and
instructions.

Figure 2-2-2: Lubrication Specifications

OM2248 Rev B

Page 67 of 104

«
...
66
67
68
69
70
...
»

Содержание 6400 Tier 4










































































































Отзывы:

Нет отзывов

Похожие инструкции для 6400 Tier 4

Бренд: HQ Страницы: 76

Бренд: R&S Страницы: 40

Бренд: Lantronix Страницы: 142

Бренд: 3onedata Страницы: 7

Бренд: T-TeleSec Страницы: 21

Бренд: PBI Страницы: 31

HD67D36-B2-868MHz

Бренд: ADF Web Страницы: 31

Бренд: B&K Страницы: 2

Бренд: ICP DAS USA Страницы: 2

Бренд: Casti Страницы: 4

Бренд: Missing Link Страницы: 8

Бренд: de Gier Страницы: 26

Бренд: ICT Страницы: 2

Бренд: Defort Страницы: 40

Бренд: GoMax Electronics Страницы: 12

ProView PVR-8140

Бренд: Harmonic Страницы: 2

Бренд: Patton electronics Страницы: 16

Бренд: TDK-Lambda Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды