ITW GSE 6400 Tier 4 Скачать руководство пользователя страница 46

Страница: 46 / 105

Operation Manual – ITW GSE 6400 Tier 4

10) Real Time Clock Setup

a) This set of sub-menu s allows the user to adjust the internal clock to the correct local time.

b) Go into the Setup Menu and then scroll up or down to the Real-Time Clock Setup submenu. Press

the center

●

button to enter the submenu, and then press the

●

button again to allow the value to

be changed. Press the up or down arrow buttons to change the selection. Press the center

●

button

to record the new value. Press the LEFT arrow button to exit the submenu and return to the
submenu list.

11) Date/Time Format

a) The date and time format that is displayed on all the screens and reports can be adjusted using this

submenu. The selection is a 24 hour clock and DD:MM:YYYY date format or a 12 hour clock with
the MM:DD:YYYY date format.

b) Go into the Setup Menu and then scroll up or down to the Date/Time Format submenu. Press the

center

●

button to enter the submenu, and then press the

●

button again to allow the value to be

changed. Press the up or down arrow buttons to change the selection. Press the center

●

button to

record the new value. Press the LEFT arrow button to exit the submenu and return to the submenu
list.

12) Ethernet Configuration

a) The sub-menu s allows the user to enter the Ethernet IP address, Subnet Mask, Gateway address

and DNS1 values for TCP/IP communications with a BMS or RMS central monitoring system.

b) Go into the Setup Menu and then scroll up or down to the Ethernet Configuration submenu. Press

the center

●

button to enter the submenu, and then press the

●

button again to allow the value to

be changed. Press the up or down arrow buttons to change selection. Press the center

●

button to

record the new value. Press the LEFT arrow button to exit the submenu and return to the submenu
list.

13) Modbus Slave Address

a) If the unit will be part of an RS-485 Modbus RTU BMS/RMS monitoring system, it must be assigned

a Modbus Slave Address. This sub-menu allows the user to enter the slave address.

b) Go into the Setup Menu and scroll up or down to the Modbus Slave Address submenu. Press

center

●

button to enter the submenu, and press the

●

button again to allow the value to changed.

Press the up or down arrow buttons to change the selection. Press the center

●

button to record the

new value. Press the LEFT arrow button to exit the submenu and return to the submenu list.

14) LED Brightness

a) The unit status LED’s have three brightness levels. The default is set to medium.

b) Go into the Setup Menu and then scroll up or down to the LED Brightness submenu. Press the

center

●

button to enter the submenu, and then press the

●

button again to allow the value to be

changed. Press the up or down arrow buttons to change the selection. Press the center

●

button to

record the new value. Press the LEFT arrow button to exit the submenu and return to the submenu
list.

15) Unit of Measure

a) This submenu is used to set the unit of measurements to Metric or Imperial.

b) Go into the Setup Menu and then scroll up or down to the Unit of Measure submenu. Press the

center

●

button to enter the submenu, and then press the

●

button again to allow the value to be

changed. Press the up or down arrow buttons to change the selection. Press the center

●

button to

record the new value. Press the LEFT arrow button to exit the submenu and return to the submenu
list.

OM2248 Rev B

Page 45 of 104

Содержание 6400 Tier 4










































































































Результаты поиска

Содержание 6400 Tier 4

Отзывы:

Похожие инструкции для 6400 Tier 4

Бренды по названию

Популярные бренды

ITW GSE 6400 Tier 4, Руководство по эксплуатации

Результаты поиска

Содержание 6400 Tier 4

Отзывы:

Похожие инструкции для 6400 Tier 4

Бренды по названию

Популярные бренды