ITW GSE 6400 Tier 4 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 105

background image

Operation Manual – ITW GSE 6400 Tier 4

To allow the user/operator to use the converter, it is possible to postpone the battery change, by
pressing the

◄

(left arrow) push button. The warning message occurs 90 seconds after the unit is

powered on or the output contactor(s) are opened (the unit is in Standby Mode). If this message is
ignored for 6 months, the controls will be locked out and the below failure message will be displayed.

Fig. 8.2.2

The battery must be changed before the unit can be operated again.

To ensure high reliability of the back-up battery, the only type of battery that can be used on
the Control Board is the Panasonic BR-2032

Go into the Setup Menu and then scroll up or down to the Confirm Battery Replaced submenu. Press
the center

●

button to enter the submenu, and then press the

●

button again to allow the value to be

changed. Press the up or down arrow buttons to change the selection. Press the center

●

button to

record the new value. Press the LEFT arrow button to exit the submenu and return to the submenu list.

19) Language

This submenu is used to change the language that all of the display screens, messages, alarms and
reports are displayed in. The unit comes with English, French, German, Italian, Polish, Portuguese,
Czech, Russian, Turkish and Spanish already installed. Other languages can be added as required.
The default is set to English.
Go into the Setup Menu and then scroll up or down to the Language submenu. Press the center

●

button to enter the submenu, and then press the

●

button again to allow the value to be changed. Press

the up or down arrow buttons to change the selection. Press the center

●

button to record the new

value. Press the LEFT arrow button to exit the submenu and return to the submenu list.

OM2248 Rev B

Page 47 of 104

«
...
46
47
48
49
50
...
»

Содержание 6400 Tier 4










































































































Отзывы:

Нет отзывов

Похожие инструкции для 6400 Tier 4

Бренд: Barco Страницы: 2

Бренд: Baum Страницы: 32

Mobitronic 8100-012VS

Бренд: Waeco Страницы: 7

Бренд: B&B Electronics Страницы: 2

S-1000MM-M2xx05

Бренд: Perle Страницы: 12

THE-S55P3BB-USW

Бренд: Tabuchi Electric Страницы: 64

PROWATT SW SW 1000

Бренд: Xantrex Страницы: 38

Бренд: Hagerman Audio Labs Страницы: 6

Atlona OmniStream 122

Бренд: Panduit Страницы: 12

Бренд: Elation Страницы: 4

Бренд: Transition Networks Страницы: 5

Бренд: Caen ELS Страницы: 52

Бренд: AIMS Power Страницы: 10

Бренд: Moxa Technologies Страницы: 2

Бренд: Planet Страницы: 63

Бренд: A-TS TECHNOLOGY Страницы: 131

Q.PEAK DUO-G5 series

Бренд: Q CELLS Страницы: 12

Бренд: Sungrow Страницы: 115

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды