Operation Manual – ITW GSE 6400 Tier 4
5) 28V Interlock Delay
a) The default value is 3.5 seconds. For safety, it is recommended to remain at this value or less.
b) Go into the Setup Menu and then scroll up or down to the 28V Interlock Delay submenu. Press the
center
●
button to enter the submenu, and then press the
●
button again to allow the value to be
changed. Press the up or down arrow buttons to change the selection. Press the center
●
button to
record the new value. Press the LEFT arrow button to exit the submenu and return to the submenu
list.
6) Aircraft Connector Insertion
a) Some aircraft power cables are equipped with a split "C" socket in the connector. This device sends
a 28 VDC signal to the unit when the connector is inserted at least 90% of the way into the aircraft
power receptacle. Set this sub-menu value to Enable when such a cable is connected to the unit.
The default value is set to Disable.
b) Go into the Setup Menu and then scroll up or down to the Aircraft Connector Insertion submenu.
Press the center
●
button to enter the submenu, and then press the
●
button again to allow the
value to be changed. Press the up or down arrow buttons to change the selection. Press the center
●
button to record the new value. Press the LEFT arrow button to exit the submenu and return to
the submenu list.
7) Cable
Temperature
a) Some aircraft cables have temperature sensors installed in the connector body and/or replaceable
nose. This sub-menu allows the unit to accept Normally Opened or Normally Closed temperature
sensor switches to be used.
b) Go into the Setup Menu and then scroll up or down to the Plug Temperature submenu. Press the
center
●
button to enter the submenu, and then press the
●
button again to allow the value to be
changed. Press the up or down arrow buttons to change the selection. Press the center
●
button to
record the new value. Press the LEFT arrow button to exit the submenu and return to the submenu
list
.
8) Allow Engine Idle
a) When this option is set to Enable, the engine will ramp up to its idle speed (1,000 RPM) and wait for
an output to be turned on. Once an output is turned on, the unit will ramp up to its running speed
(1,600, 2,000 or 2,400 RPM) and energize the generator and close the selected output contactor
when the generator is stabilised. The unit will return to idle speed five seconds after all outputs are
turned off.
b) Enter the Setup Menu and scroll up or down to the Allow Engine Idle submenu. Press the center
●
button to enter the submenu, and press the
●
button again to allow the value to be changed. Press
the up or down arrow buttons to change selection. Press the center
●
button to record the new
value. Press the LEFT arrow button to exit the submenu and return to the submenu list.
9) Automatic Engine Shutdown
a) If the engine is running at its rated speed and all outputs are off for ten (10) minutes or the total load
is less than 5 amps, the engine will automatically go into its 30 second shutdown mode when this
function is active. The Setup submenu allows this option to be activated or bypassed.
b) Enter the Setup Menu and then scroll up or down to the Automatic Engine Shutdown submenu.
Press the center
●
button to enter the submenu, and then press the
●
button again to allow the
value to be changed. Press the up or down arrow buttons to change the selection. Press the center
●
button to record the new value. Press the LEFT arrow button to exit the submenu and return to
the submenu list.
OM2248 Rev B
Page 44 of 104
Содержание 6400 Tier 4
Страница 49: ...Operation Manual ITW GSE 6400 Tier 4 c Black Box OM2248 Rev B Page 48 of 104 ...
Страница 53: ...Operation Manual ITW GSE 6400 Tier 4 OM2248 Rev B Page 52 of 104 ...
Страница 96: ...Operation Manual ITW GSE 6400 Tier 4 This page is intentionally left blank OM2248 Rev B Page 95 of 104 ...
Страница 104: ...OM2248 Rev B Page 103 of 104 ...
