ITW GSE 6400 Tier 4 Скачать руководство пользователя страница 65

Страница: 65 / 105

Operation Manual – ITW GSE 6400 Tier 4

“G” Checks and Operations (Over 10,000 Hours).

1) Engine.

a. Refer to Cummins Engine Manual for recommended maintenance and overhaul.

2) Engine/ Generator Assembly

a. Note: All Generator Overhaul items to be performed by a qualified generator/ motor

facility

b. Replace Generator Bearings

i. Contact Factory for Detailed Instructions

c. Inspect Front and Rear Bearing Housings

i. Bearing is a press fit, contact the factory for detailed instructions

d. Inspect Generator Shaft for Wear

i. Replace Rotor Assembly if required. Contact the factory for detailed

instructions.

e. Replace engine and generator shock mounts.

i. Contact factory for detailed instructions

Seasonal

Maintenance

Checks

Spring/Fall

(Engine).

3) Check Fan Mounting.

a) Check fan to be sure it is securely mounted.

b) Check for fan wobble and/or broken/cracked blades.

c) Check fan hub and crankshaft pulley for secure mounting. (2) Check cooling system each

spring and fall. Clean if necessary. (3) Check All Hoses.

4) In addition to daily checks of hoses for leaks, inspect hoses thoroughly each time the cooling

system is cleaned and serviced.

a) Inspect for signs of deterioration and collapse. Inspect for cracks and cuts. Inspect for

cutting and deformation caused by hose clamps. Replace hoses as required.

5) Check thermostat and seals each fall when cooling system is serviced.

OM2248 Rev B

Page 64 of 104

Содержание 6400 Tier 4










































































































Результаты поиска

Содержание 6400 Tier 4

Отзывы:

Похожие инструкции для 6400 Tier 4

Бренды по названию

Популярные бренды

ITW GSE 6400 Tier 4, Руководство по эксплуатации

Результаты поиска

Содержание 6400 Tier 4

Отзывы:

Похожие инструкции для 6400 Tier 4

Бренды по названию

Популярные бренды