ITW Dynatec DYNAMINI Скачать руководство пользователя

Страница: 60 / 90

ITW Dynatec c. 2004

DYNAMINI ASU Manual #20-25

Page 8-7

Revised 1/05

CAUTION: In general, all

O-RINGS AND SEALS

must be replaced whenever

hot-melt equipment is re-assembled. All new o-rings must be lubricated with

o-ring lube (PN N07588).

CAUTION:

TAPERED PIPE THREADS

are found on air line fittings used with the

pump air supply and on the outlet filter manifold. Apply thread sealant (PN

N02892) whenever tapered pipe threaded parts are re-assembled.

CAUTION:

SOME FITTINGS

used for adhesive on the ASU have straight threads

and o-ring seals. Use of thread sealant is not necessary with these parts, but the

o-ring seals should be clean and lubricated. Tighten straight-threaded parts and

fittings until their shoulders are firmly seated. Excessive torque may damage

straight-threaded parts and the use of power wrenches is not recommended.

CAUTION:

HOT-MELT RESIDUE

must be cleaned from parts before they are

re-assembled, particularly from threaded parts. As a precaution against adhesive

residue preventing proper re-assembly, threaded parts must be re-tightened at

operating temperature.

Re-Assembly Procedures

Unless noted, the ASU’s re-assembly is simply the reverse sequence of the disassembly procedures.

However, the following “cautions” should be followed (whenever they apply) for proper re-assem-

bly:

Содержание DYNAMINI



























































































Результаты поиска

Содержание DYNAMINI

Отзывы:

Похожие инструкции для DYNAMINI

Бренды по названию

Популярные бренды

ITW Dynatec DYNAMINI, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание DYNAMINI

Отзывы:

Похожие инструкции для DYNAMINI

Бренды по названию

Популярные бренды