ITW Dynatec DYNAMINI Скачать руководство пользователя

Страница: 43 / 90

Page 7-6

Revised 1/05

ITW Dynatec c. 2004

DYNAMINI ASU Manual #20-25

Problem

Possible Cause

Solution

Hopper temperature is

higher than setpoint

(overtemp).

Display for Hopper =

EO1.

Display for Hopper =

EO2.

Hopper does not heat,

but LED is ON.

1. Hopper sensor not fully

inserted.

2. Hopper sensor (X4)

inoperative.

3. Inoperative PCB.

1. Plug connection X4 on

PCB is loose.

2. Temperature sensor in-

operative.

1. Hopper sensor short cir-

cuit.

2. Short circuit at plug con-

nection X4 on PCB.

3. Inoperative PCB.

1. Hopper fuses (F4 & F11)

inoperative on PCB.

2. Hopper heater element

is inoperative.

3. Disconnection in hopper

heater circuit.

4. Inoperative PCB.

1. Check hopper sensor.

2. Replace hopper sensor if resist-

ance does not comply with resist-

ance table.

3. Replace PCB.

1. Restore connection.

2. Replace sensor if resistance does

not comply with resistance table.

1. Replace sensor if resistance does

not comply with resistance table.

2. Check and eliminate short circuit.

3. Replace PCB.

1. Insert new fuse(s) and observe

ASU. If fuse(s) blows again, check

for a short circuit in heater.

2. Replace hopper if element’s re-

sistance does not comply with re-

sistance table.

Note: remove wires

from both heater elements when

measuring.

3. Check and repair (see wiring dia-

gram).

4. Replace PCB.

Heater

25 Ohms

Содержание DYNAMINI



























































































Результаты поиска

Содержание DYNAMINI

Отзывы:

Похожие инструкции для DYNAMINI

Бренды по названию

Популярные бренды

ITW Dynatec DYNAMINI, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание DYNAMINI

Отзывы:

Похожие инструкции для DYNAMINI

Бренды по названию

Популярные бренды