ITW Dynatec DYNAMINI Скачать руководство пользователя

Страница: 19 / 90

ITW Dynatec c. 2004

DYNAMINI ASU Manual 20-25

Page 3-7

Revised 1/05

Storage and Disposal of the DYNAMINI Application System

Temporary Storage of the Unit

1. Flush the adhesive application system with flushing fluid (PN L15653), following the

instructions detailed in chapter 6 of this manual.

2. Clean or replace both the output filter and the primary filter, following instructions detailed

in chapter 6.

3. Shut OFF all pressure and power sources.

4. Release residual air pressure.

5. Remove all residual adhesive and wipe components clean.

6. Remove all air lines and all power supply cables.

7. Pack the unit in a corrosion-proof manner.

8. Store the unit in such a way that it is protected from damage.

Disposal of the Unit

1. Shut OFF all pressure and power sources.

2. Release residual air pressure.

3. Remove all residual adhesive.

4. Remove all air and adhesive supply hoses and all power supply cables.

5. Dismantle all components and sort into mechanical and electrical components.

6. Arrange for all components to be recycled.

Содержание DYNAMINI



























































































Результаты поиска

Содержание DYNAMINI

Отзывы:

Похожие инструкции для DYNAMINI

Бренды по названию

Популярные бренды

ITW Dynatec DYNAMINI, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание DYNAMINI

Отзывы:

Похожие инструкции для DYNAMINI

Бренды по названию

Популярные бренды