ITW Dynatec DYNAMINI Скачать руководство пользователя | Manualshive

Страница: 27 / 90

background image

ITW Dynatec c. 2004

DYNAMINI ASU Manual #20-25

Page 5-3

Revised 1/05

Keypad Locking

It is possible to lock or unlock the controller in order to restrict programming changes. To change the
code which is necessary to over-ride or unlock the keypad lock, see Service Functions.

Note: the ASU is shipped with de-activated keypad lock. If the keypad lock must be used, an access
code must be programmed prior to locking the keypad.

Locking or Unlocking the Keypad

Important Note: the controller must be in the Temperature Display mode in order to allow
locking or unlocking of the keypad.

&

Press the Down Scroll key, then hold and press the
Service icon key.

You will see “Loc” to indicate that the Keypad Lock is
active.

Press the Down Scroll key, then hold and press the
Service icon key.

You will see “Cod” to indicate that the access code is
required.

Enter your access code by scrolling up or down. Default
code = “ -- -- --”.

Confirm your code input by pressing Tank key.

&

or

Locking the Keypad

Unlocking the Keypad

Notes:
1. Once the keypad lock is active, unauthorized programming is not possible, even after turning the
ASU OFF, then back ON again.
2. Once the keypad lock is unlocked, programming is possible until the ASU is turned OFF, then back
ON or the keypad is locked again.
3. If the keypad must be unlocked permanently, the access code must must be de-activated in the Ser-
vice Functions.

«
...
25
26
27
28
29
...
»

Содержание DYNAMINI



























































































Отзывы:

Нет отзывов

Похожие инструкции для DYNAMINI

Бренд: Makita Страницы: 16

Бренд: Westfalia Страницы: 18

Бренд: Parkside Страницы: 80

Бренд: Chicago Pneumatic Страницы: 36

Бренд: joke Страницы: 12

Бренд: TDK-Lambda Страницы: 74

PSI 8000 3U HS PV Series

Бренд: Elektro-Automatik Страницы: 76

Бренд: APS Страницы: 156

Бренд: Gedore Страницы: 246

Бренд: Pyramid Страницы: 4

SonnenProtect 1300-AU-IN-ATS

Бренд: Sonnen Страницы: 20

Бренд: Westfalia Страницы: 19

Aliaxis CLAMP63

Бренд: FRIATEC Страницы: 12

Бренд: AC Hydraulic Страницы: 32

Бренд: RIDGID Страницы: 1

Бренд: Matco Tools Страницы: 13

Бренд: MasterCraft Страницы: 26

Бренд: Heritage MedCall Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды