ITW Dynatec DYNAMINI Скачать руководство пользователя | Manualshive

Страница: 59 / 90

background image

Page 8-6

Revised 1/05

ITW Dynatec c. 2004

DYNAMINI ASU Manual #20-25

b.

Gear Pump and Motor Removal:

1. Disconnect the motor’s electrical cable
from the ASU by unplugging it at the circuit
board
2. Remove the bolts and lockwashers which
connect the motor to the base of the unit.
3. Remove the two set screws located in the
coupling.
4. Loosen the coupling and lift out the motor.
5. To replace the gear pump, remove the four
nuts that hold the pump to the pump adapter
block.
6. Disconnect the coupling.
7. Remove the pump assembly from the end
of the unit.
8. For re-assembly: slide new pump onto the
four studs. Tighten the four nuts to secure the
pump. Torque should be approximately 21
Nm (15 ft/lb) at room temperature. With
pump and hopper at 177

°

C (350

°

F), the maxi-

mum allowable torque on these nuts is 41 Nm
(36 ft/lb).

c.

Gear Pump Seal (O-ring) Replacement:

1. Remove the pump from the ASU (see
instructions above, “a” or “b”).
2. Remove the external pump seal (PN
069X064) from its groove on the back of the
pump adapter plate (this is the seal located
between the adapter plate and the hopper).
Reference the pump exploded-view illustra-
tion in Chapter 10 for your specific pump.
3. Install the new seal.

d.

Gear Pump Shaft Seal Replacement:

Remove the shaft key and the four socket
head cap screws holding the seal retainer
plate. The seal (069X061) is located between
the retainer plate and the front plate assembly.

Note on the Cast-in Heaters

(See illustration on page 10-11)
The cast-in heaters installed in the base of the
hopper are not replaceable and will last the
life of the ASU.

Remove nuts to

release pump

from adapter.

Motor mount

bracket

Motor bracket screws

Remove set

screws to loosen

coupling.

Capacitor

Disconnect from terminal rail.

O-ring

069X064

Shaft Seal

Shaft Key

Front plate

assembly

Retainer plate

Remove nuts to

release pump

from adapter.

Motor bracket

screws

Remove set

screws to loosen

coupling.

Disconnect from terminal

rail

Gear Pump

Gear Motor Wiring Diagram

Capacitor

RED

BROWN

ORANGE

BLACK

7

WHITE

BLUE (120v)

BLUE (240v)

JUMPER (120v)

3

240vac: Blue Wire in

Terminal Block, No

other Jumpers used.

120vac: Blue Wire in

Capacitor, Jumper

between Terminal

Blocks.

to base

«
...
57
58
59
60
61
...
»

Содержание DYNAMINI



























































































Отзывы:

Нет отзывов

Похожие инструкции для DYNAMINI

Бренд: ABS Страницы: 8

Ultra-Lok UL4000

Бренд: Band-it Страницы: 14

Бренд: Earlex Страницы: 4

Бренд: Daxten Страницы: 2

Бренд: Gage Bilt Страницы: 9

Бренд: Gage Bilt Страницы: 13

Бренд: Makita Страницы: 11

Бренд: Makita Страницы: 4

Бренд: Makita Страницы: 8

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Start-It VEC025MB

Бренд: Vector Страницы: 8

PS 8000 2U Series

Бренд: Elektro-Automatik Страницы: 40

Бренд: ZALMAN Страницы: 4

Бренд: P.I.T. Страницы: 22

Бренд: Amazing Machinery Страницы: 29

Бренд: Hama Страницы: 48

GE-CS 18 Li-Solo

Бренд: EINHELL Страницы: 44

Бренд: Fein Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды