ITW Dynatec DYNAMINI Скачать руководство пользователя

Страница: 38 / 90

ITW Dynatec c. 2004

DYNAMINI ASU Manual #20-25

Page 7-1

Revised 1/05

Chapter 7

TROUBLESHOOTING

General Troubleshooting Notes

Note: Re-read Chapter 1 “Safety Precautions” before performing any troubleshooting or repair proce-
dures. All troubleshooting or repair must be performed by qualified, trained technicians.

DANGER

HIGH VOLTAGE

WARNING

HOT SURFACE

Dynamini systems use electrical power that can be life threatening and hot-melt adhesives that

can cause serious burns. Only qualified persons should perform service on the Dynamini sys-

tem.

Handling Printed Circuit Boards (PCBs)

CAUTION: Printed circuit boards (PCBs) should be handled using the following

procedures:

1. Wear a wrist grounding strap. If a grounding strap is not available, frequently touch a

bare metal part of the ASU (unpainted frame, mounting screw, etc.) to safely discharge

any electrostatic buildup on your body.

2. Handle a PCB by its edges only. Don’t grip a PCB across its surface.

3. When removed from the ASU, each PCB must be individually packaged inside a

metallized, static drain envelope. Do not place the removed PCB on a table, counter,

etc. until it has first been placed in or on a static drain envelope.

4. When handing a PCB to another person, touch the hand or wrist of that person to

eliminate any electrostatic charge

before

you hand the PCB to him.

5. When unwrapping a PCB from its static drain envelope, place the envelope on a

grounded, nonmetallic

surface.

6. To cushion PCBs for shipment, use only static-drain bubble pack. Do not use foam

peanuts or bubble pack not known to be static draining.

DANGER HIGH VOLTAGE

Before unplugging connectors from the I/O PCBs, ground yourself to the

ASU by touching any available unpainted cool metal surface, mounting

screws, etc. This will avoid electrical discharge to the PCB assembly when you are remov-

ing and replacing connectors.

Содержание DYNAMINI



























































































Результаты поиска

Содержание DYNAMINI

Отзывы:

Похожие инструкции для DYNAMINI

Бренды по названию

Популярные бренды

ITW Dynatec DYNAMINI, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание DYNAMINI

Отзывы:

Похожие инструкции для DYNAMINI

Бренды по названию

Популярные бренды