ITW Dynatec DYNAMINI Скачать руководство пользователя

Страница: 44 / 90

ITW Dynatec c. 2004

DYNAMINI ASU Manual #20-25

Page 7-7

Revised 1/05

Hopper does not heat,

and LED is OFF.

Hose (or Head) is not

heating.

Hose

(or

Head) LED on the

PCB is ON.

Hose (or Head) is not

heating.

Hose

(or

Head) LED on the PCB

is OFF.

Hose (or Head) actual

temperature is much

higher than setpoint.

Problem

Possible Cause

Solution

1. Inoperative Control PCB.

1. Disconnection between

ASU and Hose (or

between Hose and Head).

2. Hose (or Head) fuse(s) on

the PCB is inoperative.

3. Loose plug connection on

PCB.

4. Heating element inopera-

tive.

1. Inoperative PCB.

2. Sequential Startup is

active.

1. Inoperative Hose (or

Head) triac on PCB

(corresponding PCB LED

is OFF).

2. Inoperative Hose (or

Head) temperature sensor

(corresponding PCB LED

is ON).

1. Replace PCB.

1. Check plug connections.

2. Insert new fuse(s). If fuse blows

again, check for a short circuit in

heater.

3. Check connectors X8 and X11

and restore connection.

4. Check resistance and compare to

resistance table.

a. For head: if heater cartridge

is inoperative, replace heater.

b. For hose: if heating element

is inoperative, replace hose.

1. Replace PCB.

2. Wait until hopper has reached

setpoint or re-program the heat-up

mode (see pg. 5-6).

1. Replace PCB.

2. Check resistance and compare to

resistance table.

a. For head: if sensor is

inoperative, replace sensor.

b. For hose: if sensor is

inoperative, replace hose.

Fuses:
F2 & F9 = Hose 1
F3 & F10 = Head 1
F5 & F12 = Hose 2
F6 & F13 = Head 2

Содержание DYNAMINI



























































































Результаты поиска

Содержание DYNAMINI

Отзывы:

Похожие инструкции для DYNAMINI

Бренды по названию

Популярные бренды

ITW Dynatec DYNAMINI, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание DYNAMINI

Отзывы:

Похожие инструкции для DYNAMINI

Бренды по названию

Популярные бренды