ITT Goulds Pumps 3500XD Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 50

background image

Figure 27:

CAUTION:

Pump and components are heavy. Failure to properly lift and support equipment could result in
serious physical injury or damage to pumps. Steel toed shoes must be worn at all times.

1.

Install shaft flingers. Note: flingers are required on "L" group pumps only. Prop shaft up-
right and apply a light coat of oil to the shaft turn for the flinger. Place flinger on shaft
and push on by hand as far as possible. Use a block of wood and a hammer to seat the
flinger in place against the shaft shoulder. The block should be set against the thin wall
of the flinger that forms the cylindrical mounting surface (see Figure 28). Flip the shaft
to place the other end up and install the second flinger in the same manner.

Figure 28: Shaft flinger installation

NOTICE:

Never use a hammer to drive shaft through bearings. Severe shaft and bearing damage may
occur.

"S" and "L" Group

1.

Refer to Figure 27 for installation of the four point thrust

bearing. Remove bearings from boxes and orient as shown in Figure 26. NOTE: Items 1 and 3
are not interchangeable. Heat and mount item 1 against shaft shoulder. Lubricate and install item
2. Heat and install item 3. Heat and install item 4.

6.5 Reassembly of pump

44

3500XD Installation, Operation and Maintenance Instructions

«
...
44
45
46
47
48
...
»

Содержание Goulds Pumps 3500XD



















































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3500XD

Бренд: Panasonic Страницы: 224

Бренд: Zilmet Страницы: 10

HydraPump Smart

Бренд: Watershed Innovations Страницы: 11

Бренд: Zip Страницы: 16

Бренд: Tebas Страницы: 14

Бренд: RainWater Harvesting Страницы: 3

Бренд: ProMinent Страницы: 20

Бренд: Bard Страницы: 49

Бренд: Grundfos Страницы: 160

Бренд: A.O. Smith Страницы: 43

Бренд: Durapac Страницы: 11

Бренд: KNF Страницы: 88

Бренд: Galletti Страницы: 60

Бренд: O-SO Pure Страницы: 16

Бренд: Watson-Marlow Страницы: 12

Бренд: Xylem Страницы: 28

Бренд: HARNITEK Страницы: 28

Бренд: HERBORNER pumpentechnik Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды