ITT Goulds Pumps 3500XD Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 50

background image

6 Maintenance

6.1 Lubrication

NOTICE:

Operation of the unit without proper lubrication will cause bearing failure, and pump seizure.

NOTICE:

Pumps are shipped without oil. Oil lubricated bearings must be lubricated at the job site.

Oil lubricated bearings must be lubricated at the job site. Remove fill plug and add oil until level is at the
center of the sight glass. Replace fill plug.

Change the oil after 2000 hours for new bearings, thereafter every 2000 operating hours or 3 months
(whichever comes first). Change more often if oil becomes contaminated with dirt or water.

A high quality turbine oil with rust and oxidation inhibitors should be used. For the majority of operational
conditions, bearing temperatures will run between 60°C (140°F) and 82°C (180°F). In this range, an oil of
ISO viscosity grade 68 at 40°C (105°F) is recommended. If bearing temperatures exceed 82°C (180°F),
use of ISO viscosity grade 100 is recommended.

Acceptable Oils

Exxon Teresstic EP 68

Chevron GTS Oil 68

Mobil Mobil DTE 26 300 SSU @ 38°C (100°F)

Gulf Gulf Harmony 68

Phillips Magnus Oil Grade 315

Phillips MM motor oil SAE 20-20W

Phillips HDS motor oil SAE 20-20W

Table 5: Lubricating oil requirements

Bearing Temperature

below 82°C

(180°F)

Bearing Tempera-

ture above 82°C

(180°F)

ISO Grade

VG 68

VG 100

Approx. SSU at 38°C
(100°F)

300

470

DIN 51517

C68

C100

Kinematic viscosity at
40°C (105°F

mm2/sec

68

100

6 Maintenance

34

3500XD Installation, Operation and Maintenance Instructions

«
...
34
35
36
37
38
...
»

Содержание Goulds Pumps 3500XD



















































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3500XD

Бренд: TapFlo Страницы: 31

Бренд: umbra pompe Страницы: 16

Бренд: A.O. Smith Страницы: 2

Бренд: M&C Страницы: 18

Бренд: T-MAG Страницы: 36

Бренд: WilTec Страницы: 8

Бренд: GilAir Plus Страницы: 4

Cylinder Passport

Бренд: WarmFlow Страницы: 16

Kaysun Aquantia R-32 PRO

Бренд: Frigicoll Страницы: 44

Бренд: SPERONI Страницы: 68

Бренд: Remco Страницы: 5

Бренд: UDOR Страницы: 96

Бренд: GORMAN-RUPP PUMPS Страницы: 52

Бренд: CALPAK Страницы: 35

Бренд: Homa Страницы: 32

WH FLAT 50-100L

Бренд: ArTi Страницы: 34

Sandpiper Signature Series

Бренд: Idex Страницы: 18

PWS BEV-300 Series

Бренд: Pure Water Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды