ITT Goulds Pumps 3500XD Скачать руководство пользователя страница 40

Страница: 40 / 50

NOTICE:

Mechanical seal parts may be damaged if they or adjacent parts are handled improperly.

19. Remove the adapter to bearing frame bolts (370B) and pull the adapter and stuffing box cover as an

assembly. Do not allow the stuffing box cover to strike the shaft, shaft sleeve, or any mechanical
seal part.

20. A cartridge mechanical seal is standard. Position and tighten the centering tabs and loosen the

drive collar set screws. The cartridge seal can then be removed as a unit.

21. Scribe shaft at coupling hub for proper positioning of hub during reassembly and remove hub.

To disassemble remainder of the liquid end, casing and suction sideplate, proceed as follows:

Figure 23: Slide shaft assembly from bearing frame

22. Disconnect suction and discharge flanges.
23. Remove casing hold-down bolts and move casing toward driver. If preferred, casing can be re-

moved from baseplate for further disassembly.

24. Remove suction sideplates nuts (423A).
25. Remove suction sideplate (176) by tightening the three jacking screws (370L). Be careful not to

damage the suction sideplate o-ring (412C).

To complete disassembly of power end proceed as follows:

NOTICE:

Bearing replacement is recommended whenever bearings are removed from the shaft.

NOTICE:

Never use a hammer to drive shaft through bearings. Severe shaft and bearing damage may
occur.

26. Remove the bolts (370B) which hold the frame adapter to the bearing frame. Remove the frame

adapter (108).

27. Remove the bolts (360) which hold the inboard bearing end cover to the frame. Remove the end

cover (119A) and labyrinth seal (125).

28. Remove bearing housing bolts (370C). Impeller adjustment bolts with jam nuts (370D) can be used

to assist in the removal of the shaft and bearing assembly from the bearing frame.

29. Slide the complete shaft assembly from back end of bearing frame. (See Fig. 21) This includes the

shaft, both bearings (radial and thrust), and bearing housing. Do not lose or damage bearing hous-
ing o-ring.

CAUTION:

Wear insulated gloves when using a bearing heater. Bearings will get hot and can cause physi-
cal injury.

6.3 Disassembly

3500XD Installation, Operation and Maintenance Instructions

Содержание Goulds Pumps 3500XD



















































Результаты поиска

Содержание Goulds Pumps 3500XD

Отзывы:

Похожие инструкции для Goulds Pumps 3500XD

Бренды по названию

Популярные бренды

ITT Goulds Pumps 3500XD, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps 3500XD

Отзывы:

Похожие инструкции для Goulds Pumps 3500XD

Бренды по названию

Популярные бренды