ITT Goulds Pumps 3500XD Скачать руководство пользователя страница 41

Страница: 41 / 50

30. Using a bearing puller or a press, remove the inboard cylindrical roller bearing (409). Be sure to ap-

ply the removing force to the inner race of the bearing to prevent damage to the races.

31. Be sure shaft and keyway are free of burrs and sharp edges so labyrinth seal o-ring will not be dam-

aged and remove bearing end cover (109A).

32. Slide the bearing housing (134A) off shaft.
33. Straighten "tang" in lock washer (382) and remove bearing lock nut and washer.
34. Remove coupling end bearing using a bearing puller. Care must be taken to prevent damage to

bearings. Never use a hammer to drive shaft through bearing. Protect bearing from contamination.

35. The "L" group shaft is equipped with two oil flingers (236). If the shaft is being re-used, the flingers

should not be removed, as they may be deformed during removal. If the shaft is being replaced,
new flingers should be used.

Figure 24: Oil lube

6.3 Disassembly

3500XD Installation, Operation and Maintenance Instructions

Содержание Goulds Pumps 3500XD



















































Результаты поиска

Содержание Goulds Pumps 3500XD

Отзывы:

Похожие инструкции для Goulds Pumps 3500XD

Бренды по названию

Популярные бренды

ITT Goulds Pumps 3500XD, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps 3500XD

Отзывы:

Похожие инструкции для Goulds Pumps 3500XD

Бренды по названию

Популярные бренды