ITT Goulds Pumps 3500XD Скачать руководство пользователя страница 18

Страница: 18 / 50

3 Installation

3.1 Site / foundation

A pump should be located near the supply of liquid and have adequate space for operation, mainte-
nance, and inspection.

Baseplate mounted pumps are normally grouted on a concrete foundation, which has been poured on a
solid footing. The foundation must be able to absorb any vibration and to form a permanent, rigid support
for the pumping unit.

The location and size of the foundation bolts are shown on the outline assembly drawing, provided with
the pump data package.

Foundation bolts commonly used are sleeve type (Fig. 6) and J Type (Fig. 7). Both designs permit move-
ment for final bolt adjustment.

Baseplate

Shims

Foundation

Sleeve

Dam

Bolt

Figure 6: Sleeve type bolts

Baseplate

Shims

Foundation

Dam

Bolt

Figure 7: J type bolts

3 Installation

3500XD Installation, Operation and Maintenance Instructions

Содержание Goulds Pumps 3500XD



















































Результаты поиска

Содержание Goulds Pumps 3500XD

Отзывы:

Похожие инструкции для Goulds Pumps 3500XD

Бренды по названию

Популярные бренды

ITT Goulds Pumps 3500XD, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps 3500XD

Отзывы:

Похожие инструкции для Goulds Pumps 3500XD

Бренды по названию

Популярные бренды