ITT Goulds Pumps 3500XD Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 50

background image

Preface

This manual provides instructions for the Installation, Operation, and Maintenance of the Goulds Model
3500XD Medium Consistency Pump. This manual covers the standard product plus common options that
are available. For special options, supplemental instructions are supplied. This manual must be read and
understood before installation and start-up.

The design, materials, and workmanship incorporated in the construction of Goulds pumps makes them
capable of giving trouble-free service. The life and satisfactory service of any mechanical unit, however,
is enhanced and extended by correct application, proper installation, periodic inspection, condition moni-
toring and careful maintenance. This instruction manual was prepared to assist operators in understand-
ing the construction and the correct methods of installing, operating, and maintaining these mixers.

ITT - Goulds Pumps shall not be liable for physical injury, damage or delays caused by a failure to ob-
serve the instructions for Installation, Operation, and Maintenance contained in this manual.

Warranty is valid only when genuine ITT - Goulds parts are used.

Use of the equipment on a service other than stated in the order will nullify the warranty, unless written
approval is obtained in advance from ITT - Goulds Pumps.

To assure proper installation, supervision from an authorized manufacturer’s representative is recom-
mended. Additional manuals can be obtained by contacting your local Goulds representative.

This manual explains

•

Proper Installation

•

Start-Up Procedures

•

Operation Procedures

•

Routine Maintenance

•

Mixer Overhaul

•

Troubleshooting

•

Ordering Spare or Repair Parts

Table of Contents

3500XD Installation, Operation and Maintenance Instructions

3

«
...
3
4
5
6
7
...
»

Содержание Goulds Pumps 3500XD



















































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3500XD

Бренд: Jandy Страницы: 96

Бренд: T.I.P. Страницы: 66

Бренд: SereneLife Страницы: 10

Waterfall Kit WFK8

Бренд: Beckett Страницы: 1

Бренд: York Страницы: 24

Бренд: T.I.P. Страницы: 84

Бренд: evenes Страницы: 24

AquaMax Eco Expert 20000/12V

Бренд: Oase Страницы: 231

Бренд: Takagi Страницы: 56

Бренд: CLIVET Страницы: 56

Бренд: Garland Страницы: 20

Everbilt SWJP125

Бренд: HOMEDEPOT Страницы: 12

COBRA NC 0500 B

Бренд: BUSCH Страницы: 36

Residential Indoor Gas Tankless Water Heater

Бренд: Rheem Страницы: 14

Бренд: Danfoss Страницы: 70

InverterFlex B-VFH09MA-1

Бренд: COMFORT-AIRE Страницы: 24

Бренд: evosanitary Страницы: 10

Бренд: CALEFACTIO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды