ITT Goulds Pumps 3500XD Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 50

background image

Guidelines for compliance

Compliance is fulfilled only when you operate the unit within its intended use. Do not change the condi-
tions of the service without the approval of an ITT representative. When you install or maintain explosion
proof products, always comply with the directive and applicable standards (for example, IEC/EN
60079-14).

1.

Monitoring the pump frame and liquid end temperature.

2.

Maintaining proper bearing lubrication.

3.

Ensuring that the pump is operated in the intended hydraulic range.

The ATEX conformance is only applicable when the pump unit is operated within its intended use. Oper-
ating, installing or maintaining the pump unit in any way that is not covered in the Instruction, Operation,
and Maintenance manual (IOM) can cause serious personal injury or damage to the equipment. This in-
cludes any modification to the equipment or use of parts not provided by ITT Goulds Pumps. If there is
any question regarding the intended use of the equipment, please contact an ITT Goulds representative
before proceeding.

Current IOMs are available at

https://www.gouldspumps.com/en-US/Tools-and-Resources/Literature/

or from your local ITT Goulds Pumps Sales representative.

All pumping unit (pump, seal, coupling, motor and pump accessories) certified for use in an ATEX classi-
fied environment, are identified by an ATEX tag secured to the pump or the baseplate on which it is
mounted. A typical tag would look like this:

Figure 1: Typical ATEX pump nameplate

Table 2: Temperature class definitions

Code Maximum permissible

pumpage temperature in °C | °F

Minimum permissible pumpage temperature in °C | °F

T1

450 | 842

372 | 700

T2

300 | 572

277 | 530

T3

200 | 392

177 | 350

T4

135 | 275

113 | 235

T5

100 | 212

Option not available

T6

85 | 185

Option not available

The code classification marked on the equipment must be in accordance with the specified area where
the equipment will be installed. If it is not, do not operate the equipment and contact your ITT Goulds
Pumps sales representative before proceeding.

The CE and the Ex designate the ATEX compliance. The code below reads as follows:

II - Group – Non Mining Equipment

II = Group 2

2 = Category 2

G/D = Gas and Dust present

1.5 ATEX Considerations and Intended Use

10

3500XD Installation, Operation and Maintenance Instructions

«
...
10
11
12
13
14
...
»

Содержание Goulds Pumps 3500XD



















































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3500XD

Бренд: Waters Страницы: 111

Бренд: Zoeller Страницы: 4

Бренд: Mallory Страницы: 7

Бренд: A.O. Smith Страницы: 65

Бренд: T.I.P. Страницы: 66

Goulds Marlow Series

Бренд: Xylem Страницы: 8

Бренд: Xylem Страницы: 12

Бренд: QEP Страницы: 2

Бренд: Zenit Страницы: 35

Odyssey ODYR-25-1

Бренд: Dakota Digital Страницы: 8

Бренд: Davey Страницы: 4

Бренд: NCP Страницы: 16

Hydro-Guard HG-3

Бренд: Mueller Страницы: 7

Бренд: Zoeller Страницы: 16

Бренд: STIEBEL ELTRON Страницы: 15

Бренд: vacuubrand Страницы: 88

Бренд: Xylem Страницы: 8

Бренд: Lincoln Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды