background image

 

 

SERVICE MANUAL 

 

 

© ISA, s.r.o. 2014-2015. All rights reserved.  
We reserve the right to change the specification without prior notification.  
Always check for new version of this document

www.LVL0.eu

  

Service manual V1.08     |     Nov-2015     |     LM0002-EN 

Page 82 of 97

 

 

5.6.4

 

6 way valve 

Filter maintenance is very important part of swimming pool maintenance 
tasks.  Complete  filter  cleanup  process  consists  of  several  steps  when 
coordination  is  very  important.  With  LVLØ  system,  this  is  completely 
integrated  and  can  be  performed  automatically  based  on  schedule  or  by 
single button. 

Filter cleanup mode: 

 

OFF – filter cleanup is not scheduled, no automatic cleanup process will 

be started. This is also used when there is no 6-way valve installed. 

 

2x/week – LVLØ performs automatically cleanup two times per week. 

 

1x/week – LVLØ performs automatically cleanup one time per week. 

 

Custom – cleanup will be started based on custom timer. 

Custom timer: Custom timer is used to define start and stop times according 
to needs. With 

 button, you can add new entry. There is a possibility to 

define as many entries per day as needed. For deleting  an entry, press   

button. To modify an entry, select entry and change as needed. If filtration mode is in Custom mode, and 
actual time is within defined entry, status will be changed to active, otherwise is inactive. 

After  performing  setup  or  any  changes  to  this  section,  click  „SAVE  SETTINGS”  to  save  configuration  to 
system. 

5.6.5

 

Heating 

Set  point  water  temperature:  <value>  Set  desired  swimming  pool  water 
temperature in °C. 

Water temperature: Displays measured swimming pool water temperature 
in °C. 

Ext. system temperature: Displays measured external system (solar, heating 
pump, etc.) temperature in °C. 

Cooling:  <ON/OFF>  Cooling  function  can  be  enabled  here.  Cooling  allows 
LVLØ  system  to  control  electric  heating  valve  in  case  that  desired 
temperature  is  lower  than  actual  swimming  pool  water  temperature  and 
external system temperature. 

After performing setup or any changes to this section, click „SAVE SETTINGS” 
to save configuration to system. 

 

 

 

Содержание LVLO


































































































Отзывы: