Invacare TDX 3 Скачать руководство пользователя страница 49

Страница: 49 / 72

Part No. 1114809

TDX WHEELCHAIRS

SEAT

SECTION 6

This Section Includes the Following:
Replacing Seat Positioning Strap

Adjusting the Seat Position on the Seat Frame

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure

that all attaching hardware is tightened securely - otherwise injury or

damage may result.

REPLACING SEAT POSITIONING STRAP (FIGURE 1)

STANDARD/ADJUSTABLE SEAT FRAMES

1. Remove the seat cushion from the seat pan.
2. Move the flip back armrests out of the

way. Refer to USING/ADJUSTING FLIP

BACK ARMRESTS in Section 5

of this

manual.

3. Remove the two (2) mounting screws,

quick release pin tabs, spacers, and

locknuts that secure the seat pan and

seat positioning straps to the seat frame.

4. Remove the two (2) halves of the seat

positioning strap from the rear seat

frame.

NOTE: Quick release pin tabs are positioned un-

derneath the seat positioning strap.

5. Reposition the two (2) NEW seat

positioning strap halves underneath seat

rails.

6. Reinstall the two (2) mounting screws,

quick release pin tabs, spacers, and

locknuts that secure the seat pan and

seat positioning straps to the seat frame

and torque to 75-inch pounds.

7. Reinstall the seat cushion onto the seat

pan.

Seat

Positioning

Strap

FIGURE 1 - REPLACING SEAT

POSITIONING STRAP

Seat Pan

Locknut

Mounting

Screw

Quick

Release Pin

Tab

Spacer

Front of

Seat Frame

Rear of

Seat Frame

Seat Rail

SEAT

All manuals and user guides at all-guides.com

Содержание TDX 3









































































Результаты поиска

Содержание TDX 3

Отзывы:

Похожие инструкции для TDX 3

Бренды по названию

Популярные бренды

Invacare TDX 3, Руководство пользователя

Результаты поиска

Содержание TDX 3

Отзывы:

Похожие инструкции для TDX 3

Бренды по названию

Популярные бренды