Invacare TDX 3 Скачать руководство пользователя страница 45

Страница: 45 / 72

Part No. 1114809

TDX WHEELCHAIRS

SECTION 4

FRONT RIGGINGS

FRONT

RIGGINGS

FIGURE 15 - ADJUSTING THE HEIGHT OF THE CENTER MOUNT

ADJUSTABLE KNEE ANGLE FOOTREST - FOR ASBA SEATS

Extension Tube

Mounting Holes

Mounting

Screws

Height Adjustment

Holes

Extension

Tube

Extension

Tube

Housing

Seat Frame

Release Lever

FOR 2GTR SEATING SYSTEMS (FIGURE 16)

1. Remove the two (2) mounting screws that secure the footrest extension tube to the

extension tube housing.

*2. Remove the retaining ring on the angle adjustment pin and slide it out.
3. Adjust the footrest extension tube to the desired height and align the corresponding

holes to the mounting holes on the extension tube housing.

*4. Reinstall the angle adjustment pin and the retaining ring.
5. Reinstall the two (2)

mounting screws to

secure the footrest

extension tube to the

extension tube hous-

ing. Securely tighten.

6. Repeat STEPS 1-5 for

the other extension

tube.

*NOTE: STEPS 2 and 4 ap-

ply only to the three (3) short-

est settings for footrest

height.

Extension Tube

Housing

Extension Tube

Mounting Holes

Mounting

Screws

Extension

Tube

Seat Frame

Angle

Adjustment

Pin

Retaining Ring

Height Adjustment

Holes

FIGURE 16 - ADJUSTING THE HEIGHT OF THE

CENTER MOUNT ADJUSTABLE KNEE ANGLE

FOOTREST - 2GTR SEATING SYSTEMS

Release

Lever

All manuals and user guides at all-guides.com

Содержание TDX 3









































































Результаты поиска

Содержание TDX 3

Отзывы:

Похожие инструкции для TDX 3

Бренды по названию

Популярные бренды

Invacare TDX 3, Руководство пользователя

Результаты поиска

Содержание TDX 3

Отзывы:

Похожие инструкции для TDX 3

Бренды по названию

Популярные бренды