Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011 Скачать руководство пользователя страница 246

Страница: 246 / 290

Processor Configuration Registers

246

Datasheet, Volume 2

58:57

RO-V

Uncore

IOTLB Actual Invalidation Granularity (IAIG)

Hardware reports the granularity at which an invalidation request

was processed through this field when reporting invalidation

completion (by clearing the IVT field).
The following are the encodings for this field.
00 = Reserved. This indicates hardware detected an incorrect

invalidation request and ignored the request. Examples of

incorrect invalidation requests include detecting an

unsupported address mask value in Invalidate Address

01 = Global Invalidation performed. This could be in response to a

global, domain-selective, or page-selective invalidation

request.

10 = Domain-selective invalidation performed using the domain-id

specified by software in the DID field. This could be in

response to a domain-selective or a page-selective

invalidation request.

11 = Domain-page-selective invalidation performed using the

address, mask and hint specified by software in the

Invalidate Address register and domain-id specified in DID

field. This can be in response to a page-selective invalidation

request.

56:50

Reserved

Uncore

Drain Reads (DR)

This field is ignored by hardware if the DRD field is reported as

clear in the Capability register. When the DRD field is reported as

set in the Capability register, the following encodings are supported

for this bit:
0 = Hardware may complete the IOTLB invalidation without

draining any translated DMA read requests.

1 = Hardware must drain DMA read requests.

Uncore

Drain Writes (DW)

This bit is ignored by hardware if the DWD field is reported as clear

in the Capability register. When the DWD field is reported as set in

the Capability register, the following encodings are supported for

this bit:
0 = Hardware may complete the IOTLB invalidation without

draining DMA write requests.

1 = Hardware must drain relevant translated DMA write requests.

47:40

Reserved

39:32

00h

Uncore

Domain-ID (DID)

This field indicates the ID of the domain whose IOTLB entries need

to be selectively invalidated. This field must be programmed by

software for domain-selective and page-selective invalidation

requests.
The Capability register reports the domain-id width supported by

hardware. Software must ensure that the value written to this field

is within this limit. Hardware ignores and does not implement bits

47:(32+N), where N is the supported domain-id width reported in

the Capability register.

31:0

Reserved

B/D/F/Type:

0/0/0/GFXVTBAR

Address Offset:

108–10Fh

Reset Value:

0200000000000000h

Access:

RW-V, RW, RO-V

Size:

64 bits

BIOS Optimal Default

0000000000000h

Bit

Attr

Reset

Value

RST/

PWR

Description

Содержание 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011



































































































































































































































































































Результаты поиска

Содержание 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Отзывы:

Похожие инструкции для 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Бренды по названию

Популярные бренды

Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011, Техническое описание

Результаты поиска

Содержание 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Отзывы:

Похожие инструкции для 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Бренды по названию

Популярные бренды