Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011 Скачать руководство пользователя страница 178

Страница: 178 / 290

Processor Configuration Registers

178

Datasheet, Volume 2

2.10.42 SLOTSTS—Slot Status Register

This is for PCI Express Slot related registers.

B/D/F/Type:

0/6/0/PCI

Address Offset:

BA–BBh

Reset Value:

0000h

Access:

RO, RO-V, RW1C

Size:

16 bits

BIOS Optimal Default

00h

Bit

Attr

Reset

Value

RST/

PWR

Description

15:9

Reserved

Uncore

Reserved for Data Link Layer State Changed (DLLSC)

This bit is set when the value reported in the Data Link Layer Link

Active field of the Link Status register is changed. In response to a

Data Link Layer State Changed event, software must read the Data

Link Layer Link Active field of the Link Status register to determine

if the link is active before initiating configuration cycles to the hot

plugged device.

Uncore

Reserved for Electromechanical Interlock Status (EIS)

If an Electromechanical Interlock is implemented, this bit indicates

the current status of the Electromechanical Interlock.
0 = Electromechanical Interlock Disengaged

1 = Electromechanical Interlock Engaged

RO-V

Uncore

Presence Detect State (PDS)

In band presence detect state:
0 = Slot Empty

1 = Card present in slot
This bit indicates the presence of an adapter in the slot, reflected

by the logical "OR" of the Physical Layer in-band presence detect

mechanism and, if present, any out-of-band presence detect

mechanism defined for the slot's corresponding form factor. Note

that the in-band presence detect mechanism requires that power

be applied to an adapter for its presence to be detected.
Consequently, form factors that require a power controller for hot-

plug must implement a physical pin presence detect mechanism.
0 = Slot Empty

1 = Card Present in slot
This register must be implemented on all Downstream Ports that

implement slots. For Downstream Ports not connected to slots

(where the Slot Implemented bit of the PCI Express Capabilities

Uncore

Reserved for MRL Sensor State (MSS)

This register reports the status of the MRL sensor if it is

implemented.
0 = MRL Closed

1 = MRL Open

Uncore

Reserved for Command Completed (CC)

If Command Completed notification is supported (as indicated by

No Command Completed Support field of Slot Capabilities

and the Hot-Plug Controller is ready to accept a subsequent

command. The Command Completed status bit is set as an

indication to host software that the Hot-Plug Controller has

processed the previous command and is ready to receive the next

command; it provides no guarantee that the action corresponding

to the command is complete.
If Command Completed notification is not supported, this bit must

be hardwired to 0b.

Содержание 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011



































































































































































































































































































Результаты поиска

Содержание 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Отзывы:

Похожие инструкции для 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Бренды по названию

Популярные бренды

Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011, Техническое описание

Результаты поиска

Содержание 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Отзывы:

Похожие инструкции для 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Бренды по названию

Популярные бренды