Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011 Скачать руководство пользователя страница 173

Страница: 173 / 290

Datasheet, Volume 2

173

Processor Configuration Registers

2.10.39 LSTS—Link Status Register

This register indicates PCI Express link status.

B/D/F/Type:

0/6/0/PCI

Address Offset:

B2–B3h

Reset Value:

1001h

Access:

RW1C, RO-V, RO

Size:

16 bits

BIOS Optimal Default

Bit

Attr

Reset

Value

RST/

PWR

Description

RW1C

Uncore

Link Autonomous Bandwidth Status (LABWS)

This bit is set to 1b by hardware to indicate that hardware has

autonomously changed link speed or width, without the port

transitioning through DL_Down status, for reasons other than to

attempt to correct unreliable link operation.
This bit must be set if the Physical Layer reports a speed or width

change was initiated by the downstream component that was

indicated as an autonomous change.

RW1C

Uncore

Link Bandwidth Management Status (LBWMS)

This bit is set to 1b by hardware to indicate that either of the

following has occurred without the port transitioning through

DL_Down status:
A link retraining initiated by a write of 1b to the Retrain Link bit has

completed.

Note:

This bit is Set following any write of 1b to the Retrain Link

bit, including when the Link is in the process of retraining for some

other reason.
Hardware has autonomously changed link speed or width to

attempt to correct unreliable link operation, either through an

TXTSSM time-out or a higher level process.
This bit must be set if the Physical Layer reports a speed or width

change was initiated by the downstream component that was not

indicated as an autonomous change.

RO-V

Uncore

Data Link Layer Link Active (Optional) (DLLLA)

This bit indicates the status of the Data Link Control and

Management State Machine. It returns a 1b to indicate the

DL_Active state, 0b otherwise.
This bit must be implemented if the corresponding Data Link Layer

Active Capability bit is implemented. Otherwise, this bit must be

hardwired to 0b.

Uncore

Slot Clock Configuration (SCC)

0 = The device uses an independent clock irrespective of the

presence of a reference on the connector.

1 = The device uses the same physical reference clock that the

platform provides on the connector.

RO-V

Uncore

Link Training (TXTRN)

This bit indicates that the Physical Layer TXTSSM is in the

Configuration or Recovery state, or that 1b was written to the

Retrain Link bit but Link training has not yet begun. Hardware

clears this bit when the TXTSSM exits the Configuration/Recovery

state once Link training is complete.

Содержание 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011



































































































































































































































































































Результаты поиска

Содержание 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Отзывы:

Похожие инструкции для 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Бренды по названию

Популярные бренды

Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011, Техническое описание

Результаты поиска

Содержание 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Отзывы:

Похожие инструкции для 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 2 01-2011

Бренды по названию

Популярные бренды