Instruo arbhar Скачать руководство пользователя страница 27

Страница: 27 / 50

Wavetable Mode

Turning the

Length

knob fully anticlockwise forces

arbhar

to crossfade

into a

Wavetable Synthesis Engine

. The wavetable is derived from a

single-cycle loop of the captured content within the layer.

•

Both

Grain Direction Indicators

are illuminated amber when this

mode is active.

•

The pitch of the

Wavetable Synthesis Engine

is calibrated to

produce a C note when the

Pitch

knob is set to its centre position.

•

The

Pitch Deviation

parameter functions in its normal manner.

•

The

Scan

and

Spray

parameters will change the position in the layer

from which the wavetable is derived.

•

The

Intensity

parameter changes in functionality to be an update rate

control for the wavetable content (

Scan

Spray

, and

Pitch Deviation

The fastest update rate is found when the

Intensity

knob is at its

centre position.

•

Moving the

Intensity

knob to either of its extreme positions will

disable its continuous oscillation. In either of these extreme positions,
the

Strike Button

and

Strike Input

can be used to trigger a short note

via the

Strike Granular Engine

. These notes are 15% louder than the

continuous oscillation and can be used to accentuate
continuous oscillation.

Содержание arbhar



















































Результаты поиска

Содержание arbhar

Отзывы:

Похожие инструкции для arbhar

Бренды по названию

Популярные бренды

Instruo arbhar, Руководство пользователя

Результаты поиска

Содержание arbhar

Отзывы:

Похожие инструкции для arbhar

Бренды по названию

Популярные бренды