Instruo arbhar Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 50

background image

12

Granular Synthesis

There are two separate granular engines within

arbhar

. The

Continuous

Granular Engine

is controlled by the

Intensity

parameter. The

Strike

Granular Engine

is controlled by the

Strike Input

and

Strike Button

.

By default, 24 grains can be generated polyphonically from the

Continuous Granular Engine

and 20 grains can be generated

polyphonically from the

Strike Granular Engine

. A total of 44 grains

can be played polyphonically between both granular engines.

Intensity:

The

Intensity

parameter sets the amount of generated grains

from the

Continuous Granular Engine

.

•

The maximum number of grains are generated when the knob is in
its centre position.

•

Turning the knob anticlockwise from its centre position will decrease
the number of grains. Any knob setting anticlockwise of its centre
position will generate grains at the same amplitude and set a
synchronous grain generation pattern.

•

Turning the knob clockwise from its centre position will decrease the
number of grains. Any knob setting clockwise of its centre position
will generate grains at random amplitudes and set asynchronous
grain generation.

HIGH

RANDOM

DISTRIBUTION

EVEN

DISTRIBUTION

«
...
10
11
12
13
14
...
»

Содержание arbhar



















































Отзывы:

Нет отзывов

Похожие инструкции для arbhar

ShareCenter Pulse DNS-320

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 4

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Бренд: D-Link Страницы: 31

Бренд: ForeScout Страницы: 28

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

Бренд: axing Страницы: 52

Бренд: MEDIATEK Страницы: 166

Бренд: AMD Страницы: 45

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: Alarm Страницы: 5

Disc Publisher XR

Бренд: Primera Страницы: 2

Бренд: Microchip Technology Страницы: 9

Бренд: Promise Technology Страницы: 26

mPCIE-ADIO16-8F Series

Бренд: Acces I/O products Страницы: 13

Бренд: M86 Security Страницы: 540

Бренд: c Страницы: 32

BreezeACCESS II

Бренд: Alvarion Страницы: 324

XBurst 2 CPU Core

Бренд: Ingenic Страницы: 143

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды