Instruo arbhar Скачать руководство пользователя страница 10

Страница: 10 / 50

Layer:

The

Layer

knob sets the currently selected layer. There are six

layers which can store up to 10 seconds of audio each.

•

They are referred to as alpha, beta, gamma, delta, epsilon,
and zeta.

•

Layer content is set at the beginning of each grain and remains
unchanged for the duration of the grain.

•

When the knob is fully clockwise and the omega

Layer Indicator

illuminated, all layers are consecutively available via the

Scan

parameter.

•

To ensure the absence of audio drop outs at extreme

Scan

parameter positions,

arbhar

will record for an extra 2 seconds at

the end of each layer.

Layer Indicators:

The

Layer Indicators

will illuminate around the

Layer

knob to indicate the currently selected layer.

•

When the knob is fully clockwise and the omega

Layer Indicator

illuminated, the currently selected layer is determined by the position
of the

Scan

parameter and indicated by the corresponding

Layer Indicator

10 SECONDS EACH

ALL LAYERS LINKED

Содержание arbhar



















































Результаты поиска

Содержание arbhar

Отзывы:

Похожие инструкции для arbhar

Бренды по названию

Популярные бренды

Instruo arbhar, Руководство пользователя

Результаты поиска

Содержание arbhar

Отзывы:

Похожие инструкции для arbhar

Бренды по названию

Популярные бренды