Inovance Monarch MCTC-CCB-A Скачать руководство пользователя страница 21

Страница: 21 / 98

Chapter 2 Mechanical and Electrical Installation

- 20 -

Type

Mark

Functions Description

Remarks

CN5

X1-X8/GND

Used for DI:

1. Photocoupler input

2. Input impedance: 4.7 kΩ

3. Voltage range upon level input: 10–30 VDC

4. Max. input current: 5 mA

GND

4.7K

(DI terminals)

GND

CN2

Y1-Y4,

M1, M2

Relay output Y1 to Y4

Normally open (NO) contact output of the

relay: 5 A, 250 VAC/28 VDC

D1 to D8

indicators

These indicators becomes ON (green) when

the external input signal is active.

D1 D2 D3 D4

D5 D6 D7 D8

D12 to D17 Relay output

indicators

These indicators becomes ON (green) when

there is a system output.

D17

D12 D13 D15

D78, D71,

D65, D60,

D55, D51,

D46, and

D41

CAN

communication

indicators

These indicators indicate the CAN

communication status of elevators 1 to 8.

Flashing: Indicating that the elevator is in the

automatic running state, with normal CAN

communication.

Steady ON: Indicating that the elevator is not

in the automatic running state, but the CAN

communication is normal.

Steady OFF: Indicating that CAN

communication of the elevator is

interrupted.

D78 D71 D65D60

D55 D51 D46D41

D85, D86,

D81 and

D80

Reserved

D79

24 V power

indicator

This indicator becomes ON after the GCB is

powered up.

D79

D94

Fault indicator

This indicator becomes ON if an elevator

runs out of the group control or there is a

communication error.

D94

NOTE

◆

To prevent external communication interference, use the shielded twisted

pair (STP) as communication cables and avoid laying them in parallel.

◆

The GCB must be powered by an independent 24 V power supply, and

cannot share the 24 V power supply with the elevator system.

Содержание Monarch MCTC-CCB-A



































































































Результаты поиска

Содержание Monarch MCTC-CCB-A

Отзывы:

Похожие инструкции для Monarch MCTC-CCB-A

Бренды по названию

Популярные бренды

Inovance Monarch MCTC-CCB-A, Руководство пользователя

Результаты поиска

Содержание Monarch MCTC-CCB-A

Отзывы:

Похожие инструкции для Monarch MCTC-CCB-A

Бренды по названию

Популярные бренды