Inovance Aonarch MD500L Series Скачать руководство пользователя

Страница: 49 / 69

- 48 -

Maintenance

Maintenance

6.1 Routine Maintenance

Check the following items daily to ensure normal running and prevent damage to the
AC drive. Copy this checklist and sign the "Checked" column after each inspection.

Inspection

Item

Inspection Points

Solutions

Checked

Motor

Inspect whether the

abnormal sounds and

vibration occur on the

motor.

◆

Check whether the mechanical

connection is normal.

◆

Check whether output phase loss

occurs on the motor.

◆

Check whether retaining screws of the

motor are tightened.

Fan

Inspect whether the

cooling fan of the AC

drive and motor work

abnormally.

◆

Check running of the cooling fan of the

AC drive.

◆

Check whether the cooling fan of the

motor is normal.

◆

Check whether the ventilation is

clogged.

◆

Check whether the ambient

temperature is within the permissible

range.

Installation

environment

Inspect whether the

cabinet and cable duct are

abnormal.

◆

Check input and output cables for

damaged insulation.

◆

Check for vibration of hanging bracket.

◆

Check whether ground bars and

terminals become loose or get

corroded.

Load

Inspect whether the

running current of the AC

drive exceeds the rated

current of the AC drive and

motor for a certain period.

◆

Check whether motor parameters are

set properly.

◆

Check whether the motor is overloaded.

◆

Check whether the mechanical

vibration is severe (allowed range: < 1

g).

Input voltage

Inspect whether the power

voltage of the main and

control circuits is within

the allowed range.

◆

Check that the input voltage is within

the allowed range.

◆

Check whether start of heavy load

exists.

Содержание Aonarch MD500L Series






































































Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды

Inovance Aonarch MD500L Series, Руководство пользователя

Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды