Inovance Aonarch MD500L Series Скачать руководство пользователя

Страница: 44 / 69

- 43 -

Trouble shooting and Solutions

Trouble shooting and Solutions

5.1 Fault Codes and Solutions

Troubleshoot the faults occurred during operating the AC drive as follows.

Display

Fault Name

Possible Causes

Solutions

Err02

Overcurrent

during

acceleration

1. The output circuit is short circuited.

2. The acceleration time is too short.

3. Manual torque boost or V/F curve is

not appropriate.

4. The power supply is too low.

5. The startup operation is performed

on the rotating motor.

6. A sudden load is added during

acceleration.

7. The AC drive model is of too small

power class.

1. Eliminate short circuit.

2. Increase the acceleration time

F0-17.

3.Adjust the manual torque boost

or V/F curve.

4. Check that the power supply is

normal.

5. Select speed tracking restart or

start the motor after it stops.

6. Remove the added load.

7. Select a drive of higher power

class.

Err03

Overcurrent

during

deceleration

1. The output circuit is short circuited.

2. The deceleration time is too short.

3. The power supply is too low.

4. A sudden load is added during

deceleration.

5. The braking resistor is not installed.

1. Eliminate short circuit.

2. Increase the deceleration

timeF0-18.

3. Check the power supply, and

ensure it is normal.

4. Remove the added load.

5. Install the braking resistor.

Err04 Overcurrent at

constant speed

1. The output circuit is short circuited.

2. The power supply is too low.

3. A sudden load is added during

operation.

4. The AC drive model is of too small

power class.

1. Eliminate short circuit.

2. Adjust power supply to normal

range.

3. Remove the added load.

4. Select a drive of higher power

class.

Err05

Overvoltage

during

acceleration

1. The DC bus voltage is too high

☆

2. An external force drives the motor

during acceleration.

3. The acceleration time is too short.

4. The braking resistor is not installed.

1. Replace with a proper braking

resistor.

2. Cancel the external force or

install braking resistor.

3. Increase the acceleration time.

4. Install a braking resistor.

Err06

Overvoltage

during

deceleration

1. The DC bus voltage is too high

☆

2. An external force drives the motor

during deceleration.

3. The deceleration time is too short.

4. The braking resistor is not installed.

1. Replace with a proper braking

resistor.

2. Cancel the external force or

install braking resistor.

3. Increase the deceleration time.

4. Install the braking resistor.

Содержание Aonarch MD500L Series






































































Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды

Inovance Aonarch MD500L Series, Руководство пользователя

Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды