Inovance Aonarch MD500L Series Скачать руководство пользователя

Страница: 6 / 69

Safety Instructions

- 5 -

DANGER

◆

Equipment installation, wiring, maintenance, inspection, or parts replacement must be

performed only by professionals.

◆

Installation, wiring, maintenance, inspection, or parts replacement must be performed only by

experienced personnel who have been trained with necessary electrical information.

◆

Installation personnel must be familiar with equipment installation requirements and relevant

technical materials.

◆

Before installing equipment with strong electromagnetic interference, such as a transformer,

install an electromagnetic shielding device for this equipment to prevent malfunctions.

Wiring

DANGER

◆

Equipment installation, wiring, maintenance, inspection, or parts replacement must be

performed only by professionals.

◆

Never perform wiring at power-on. Failure to comply will result in an electric shock.

◆

Before wiring, cut off all equipment power supplies. Wait at least 10 minutes before further

operations because residual voltage exists after power-off.

◆

Make sure that the equipment is well grounded. Failure to comply will result in an electric

shock.

◆

During wiring, follow the proper electrostatic discharge (ESD) procedures, and wear an

antistatic wrist strap. Failure to comply will result in damage to internal equipment circuits.

WARNING

◆

Never connect the power cable to output terminals of the equipment. Failure to comply may

cause equipment damage or even a fire.

◆

When connecting a drive with the motor, make sure that the phase sequences of the drive and

motor terminals are consistent to prevent reverse motor rotation.

◆

Wiring cables must meet diameter and shielding requirements. The shielding layer of the

shielded cable must be reliably grounded at one end.

◆

After wiring, make sure that no screws are fallen and cables are exposed in the equipment.

Power-on

DANGER

◆

Before power-on, make sure that the equipment is installed properly with reliable wiring and

the motor can be restarted.

◆

Before power-on, make sure that the power supply meets equipment requirements to prevent

equipment damage or even a fire.

◆

At power-on, unexpected operations may be triggered on the equipment. Therefore, stay away

from the equipment.

◆

After power-on, do not open the cabinet door and protective cover of the equipment. Failure to

comply will result in an electric shock.

◆

Do not touch any wiring terminals at power-on. Failure to comply will result in an electric

shock.

◆

Do not remove any part of the equipment at power-on. Failure to comply will result in an

electric shock.

Содержание Aonarch MD500L Series






































































Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды

Inovance Aonarch MD500L Series, Руководство пользователя

Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды