background image

Contents

 

- 8 -

Contents

Preface ...................................................................................................................................1

Revision History ....................................................................................................................2

Safety Instructions ................................................................................................................3

1 Product Information

 .....................................................................................................10

1.1  Nameplate and Model Number

 ..........................................................................10

1.2  Components

 ........................................................................................................11

1.3  Technical Data .....................................................................................................12

1.4  Overall Dimensions

 .............................................................................................13

2 Installation and Wiring

 .................................................................................................14

2.1 Installation ...........................................................................................................14

2.1.1  Installation Environment

 ........................................................................14

2.1.2  Backplate Mounting ................................................................................15

2.2  Wiring

 ...................................................................................................................16

2.2.1  Typical wiring 1 (use multi -reference input as frequency reference)

 .16

2.2.2  Typical wiring 2 (use analog input as frequency reference)

 ................17

2.2.3  Main Circuit Terminals

 ............................................................................

18

2.2.4  Control Circuit Terminals

 .......................................................................19

2.2.5  I/O extension board

 ................................................................................22

3 Panel Operations

 ..........................................................................................................24

3.1 Introduction .........................................................................................................24

3.2  Keys on the Operating Panel

 ..............................................................................24

3.3  Indicators on the Operating Panel

 .....................................................................25

4 Quick setup

 ...................................................................................................................27

4.1  Complete timing diagram for normal travel (use multi -reference as frequency 

reference)

 ......................................................................................................................27

4.2  Elevator performance fine tuning

 ......................................................................29

4.3  Setup flowchart 

 ..................................................................................................32

4.4  IGBT Enable

 ..........................................................................................................39

Содержание Aonarch MD500L Series






































































Отзывы: