Inovance Aonarch MD500L Series Скачать руководство пользователя

Страница: 48 / 69

- 47 -

Trouble shooting and Solutions

Fault Name

Possible Causes

Solutions

"HC" is displayed

at power-on.

1. The cable between the drive

board and the control board is in

poor contact.

2. The control board is damaged.

3. The motor winding or the motor

cable is shortcircuited to the

ground.

4. The power supply is too low.

1. Re-connect the 4-core and 28-

core flat cables, or seek for

maintenance.

2. Seek for maintenance.

3. Check the motor or replace it, and

check the motor cable.

4. Check the power supply according

“1.3 Technical Data

”

The display is

normal upon

power-on, but "HC"

is displayed after

start and the motor

stops immediately.

1. The cooling fan is damaged or the

rotor is locked.

2. A certain terminal is short-

circuited.

1. Replace cooling fan, or check the

machine whether it is locking the

rotor.

2. Eliminate short circuit.

Err14 is reported

frequently.

1. The carrier frequency is set too

high.

2. The cooling fan is damaged, or

the air filter is blocked.

3. Components (thermal coupler

or others) inside the drive are

damaged.

1. Reduce F0-15.

2. Replace the fan and clean the air

filter.

3. Seek for maintenance.

The motor does

not rotate after the

AC drive outputs a

non-zero reference.

1. The motor or motor cable is

damaged.

2. The motor parameters are set

improperly.

3. The cable between the drive

board and the control board is in

poor contact.

4. The drive board is faulty.

5. The rotor is locked.

1. Check the motor, or check the

cable between the drive and the

motor.

2. Check and re-set motor

parameters.

3. Re-connect the 4-core and 28-

core flat cables, or seek for

maintenance.

4. Seek for maintenance.

5. Check the machine whether it is

locking the rotor.

The DI terminals

are disabled.

1. The DI parameters are set

incorrectly.

2. The input signal is incorrect.

3. The wire jumper between OP and

+24V is in poor contact.

4. The control board is faulty.

1. Check and reset DI parameters in

group F4.

2. Check the input signals, or check

the input cable.

3. Check the jumper between OP

and +24 V.

4. Seek for maintenance.

The drive reports

overcurrent and

overvoltage

frequently.

1. The motor parameters are set

improperly.

2. The acceleration/deceleration

time is too small.

3. The load fluctuates.

1. Reset motor parameters.

2. Set proper acceleration/

deceleration time.

3. Check the machine, or seek for

maintenance.

Содержание Aonarch MD500L Series






































































Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды

Inovance Aonarch MD500L Series, Руководство пользователя

Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды